TMS320C6678多核DSP的加载配置和实现方法

程序代码正确的固化加载运行是多核DSP应用的前提和基础.简要介绍了DSP的加载器和加载过程,阐述了多核处理器件的加载配置管理方法.以TI公司的多核DSP TMS320C6678为例,介绍了多核DSP的加载模式和流程,详细阐述了EMIF16的Nor FLASH加载实现方法,可以实现多核DSP软件的正确、可靠加载运行.     

折叠V形钝体火焰稳定器原型的稳燃机制研究

为了掌握折叠V形钝体这一新型火焰稳定器的稳燃机制,采用风洞实验与混合雷诺平均/大涡模拟结合的方法对常压条件下10组不同折叠角的折叠V形钝体火焰稳定器原型进行了冷态实验与热态数值模拟研究。其中冷态实验风速10~50m/s,热态数值模拟工况为进气温度700K、来流速度50~150m/s,当量比0.3~1。通过PIV实验测得了折叠V形钝体回流区冷态流动特征,并结合数值模拟方法研究并讨论了折叠V形钝体绕流尾迹区旋涡特征;通过数值模拟研究了燃烧条件下、折叠V形钝体下游槽向驻涡结构发展变化规律。研究初步探明折叠V形钝体总压恢复系数、阻力系数、抗吹熄能力与燃烧效率优于标准钝体的原因,并发现折叠角角度较小的折叠V形钝体,尾迹中心区域无典型回流区,但仍能通过槽向驻涡结构形成驻涡稳燃速度型,该速度型有利于冷态绕流流速的恢复与热态燃气的加速。     

8mm衰减标准装置

对8mm衰减标准装置的工作原理、系统设计、主要技术特点、误差分析等进行了详细介绍,并附有测试和分析数据。该装置达到了80dB的量程、全频段和±0.003dB/10dB的准确度。     

ARM CPU CS89712与C5510 DSP的接口设计

以Cirrus Logic公司的ARM芯片和TI公司的TMS320V DSP为例,研究了ARM与DSP的数据接口———HPI接口的相关技术,并给出了在HPI接口非复用模式下,CS89712与C5510的信号连接图和嵌入式实时操作系统uCOS-II下驱动程序的部分关键源代码。     

Geostationary orbit determination using SATRE

A new strategy of precise orbit determination (POD) for GEO (Geostationary Earth Orbit) satellite using SATRE (SAtellite Time and Ranging Equipment) is presented. Two observation modes are proposed and different channels of the same instruments are used to construct different observation modes, one mode receiving time signals from their own station and the other mode receiving time signals from each other for two stations called pairs of combined observations. Using data from such a tracking network in China, the results for both modes are compared. The precise orbit determination for the Sino-1 satellite using the data from 6 June 2005 to 13 June 2005 has been carried out in this work. The RMS (Root-Mean-Square) of observing residuals for 3-day solutions with the former mode is better than 9.1 cm. The RMS of observing residuals for 3-day solutions with the latter mode is better than 4.8 cm, much better than the former mode. Orbital overlapping (3-day orbit solution with 1-day orbit overlap) tests show that the RMS of the orbit difference for the former mode is 0.16 m in the radial direction, 0.53 m in the along-track direction, 0.97 m in the cross-track direction and 1.12 m in the 3-dimension position and the RMS of the orbit difference for the latter mode is 0.36 m in the radial direction, 0.89 m in the along-track direction, 1.18 m in the cross-track direction and 1.52 m in the 3-dimension position, almost the same as the former mode. All the experiments indicate that a meter-level accuracy of orbit determination for geostationary satellite is achievable.     

星载单频GPS数据的电离层延迟改正方法分析

利用C/A码单点定位对LEO(Low Earth Orbit)卫星上的电离层延迟改正方法——"电离层比例因子法"进行了分析研究.计算的CHAMP卫星的轨道结果表明:采用电子密度峰值高度(hmF2,F2 region maximum electron density height)平均值和瞬时值计算的电离层比例因子α变化范围分别为0.3~0.4和0.2~0.65之间,两者最大差异可达0.3,相比较而言,hmF2瞬时值的结果更加合理,并且相应的大地高H方向的系统偏差要降低0.05~0.3m左右;与双频无电离层组合的普通单点定位结果相比表明该方法能较好地消除电离层一阶项所引入的H方向上的系统偏差;该方法适用的LEO卫星轨道高度范围大致在200~ 600km之间,当轨道高度超过700km时,该方法并不适用.     

伺服反馈位移传感器的现状及发展趋势

反馈位移传感器是伺服机构系统的重要组成部分,在航天型号的研制中发挥着重要作用。对目前伺服机构系统配套反馈位移传感器的功能原理、特点及应用情况进行了介绍,并对其它类型的位移传感器的性能特点进行了分析,探讨了其用于航天伺服机构系统的可行性。同时,对伺服反馈位移传感器的发展趋势进行了展望。     

高准确度惯性测量装置全温测试系统的校准

阐述了高准确度捷联惯性测量装置全温测试系统的校准测试方法。通过对软硬件进行校准测试,验证了该系统可以完成不同种类的惯性测量装置误差建模和综合测试。     

93k集成电路测试系统校准原理及实现方法研究

介绍了93k集成电路测试系统校准原理与实现方法,讨论了校准过程中的量值传递关系;以HPP-MU为例,给出了量值传递的实现过程,并分析了93k校准原理与方法在确保量值准确、一致性上的优点。     

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.