基于NFTET的高超声速飞行器鲁棒轨迹重构设计

考虑高超声速飞行器故障下安全再入飞行问题,针对飞行器发生较大故障的情况,提出了基于相邻可行轨迹存在定理(Neighboring feasible trajectory existence theorem,NFTET)的鲁棒在线轨迹重构算法。在标称情况下基于反馈线性化预测校正制导算法生成满足各种约束条件的再入轨迹;由于NFTET只适用于发生较小故障的情况,为保证较大故障下飞行器仍能以较高精度安全着陆,基于NFTET理论设计了鲁棒轨迹重构算法,得到了较高落点精度的飞行轨迹。仿真结果表明,本文所提出算法能有效解决飞行器较大故障下的安全再入轨迹重构问题,提高了飞行器的自主容错能力。     

周向总压畸变对对转压气机影响效应分析

以对转压气机为研究对象,在数值方法校验的基础上,应用全通道定常流场分析手段计算了对转压气机不同周向畸变条件下的三维流场,获取了周向总压进气畸变对该压气机性能以及流场结构的影响效应,确定了对转压气机的临界畸变角,分析了不同畸变强度对压气机性能的影响规律,探讨了周向总压畸变在对转压气机中的发展演化过程。结果表明:(a)所研究的对转压气机临界畸变角约为72°,略高于传统动-静叶排交替的压气机临界畸变角;(b)相比均匀进气工况,当畸变指数为0.24时,对转压气机失速点压比和失速裕度分别下降3%和9.6%,当畸变指数为0.5时二者分别下降8.3%和19.8%;(c)未畸变区与畸变区流体之间存在的压力梯度影响转子叶片相对来流速度。进入畸变区叶片来流相对速度减小,负荷降低,退出畸变区叶片来流相对速度增大,负荷增大;(d)上游转子使得畸变水平提高,下游转子反向旋转效应抑制了来流相对速度变化趋势,增强了气流在其叶片通道中的掺混,使得畸变水平有所下降。     

舰载直升机金属动部件寿命控制技术研究

在分析现役老龄化舰载直升机动部件载荷特点的基础上,结合直升机所处的海洋腐蚀环境,讨论了舰载直升机的损伤类型和损伤容限寿命管理方法在其寿命分析中的应用,比较了损伤容限法应用于舰载直升机动部件与应用于固定翼飞机的不同点,重点讨论了损伤容限方法应用于工程实践亟待解决的关键技术。     

浅谈量块新标准的变化

介绍了量块新标准与旧标准的差异和新标准变化的原因、目的及其对量块加工带来的影响。     

基于容差分配的直升机多约束运动系统的应用与研究

本文以某民用直升机动力舱多约束运动系统的容差分配设计为例,阐述和分析了多约束运动系统容差基准的选取、分配以及设计补偿等。可以为多约束运动系统设计提供方法和参考。     

某型水陆两栖飞机主结构铝合金材料选用分析

材料选用是飞机研制过程中的一项重要内容,选用材料的好坏直接影响飞机性能的优劣,飞机选材需要考虑多个因素。某型水陆两栖飞机按照疲劳、损伤容限设计原则进行结构设计。通过对某型水陆两栖飞机载荷工况和服役环境的分析,结合飞机基本选材原则和某型水陆两栖飞机结构设计对材料的静强度性能,疲劳、损伤容限性能,耐腐蚀性能等的要求,综合考虑铝合金材料特点、适航性、成本及供货等因素,最终提出某型水陆两栖飞机结构的铝合金材料选材方案。     

公差课教材改革势在必行

本文论述现用《公差》教材存在的弊端，从改革高等教育的高度提出某些改进措施。     

Simulation analysis for effects of bone loss on acceleration tolerance of human lumbar vertebra

The purpose of the present study was to analyze and predict the changes in acceleration tolerance of human vertebra as a result of bone loss caused by long-term space flight. A human L3–L4 vertebra FEM model was constructed, in which the cancellous bone was separated, and surrounding ligaments were also taken into account. The simulation results demonstrated that bone loss has more of an effect on the acceleration tolerance in x-direction. The results serve to aid in the creation of new acceleration tolerance standards, ensuring astronauts return home safely after long-term space flight. This study shows that more attention should be focused on the bone degradation of crew members and to create new protective designs for space capsules in the future.     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

含多裂纹连接结构损伤容限试验研究

 针对机翼典型对接结构,进行了平板空孔试样和螺栓搭接件在等幅谱及飞－续－飞谱下的多裂纹损伤容限试验,通过该试验开展多裂纹开裂模式及多裂纹扩展规律的试验研究,为多裂纹断裂力学理论分析、多裂纹结构剩余强度准则提供试验依据。