VS-CMA盲均衡算法在短波数据通信中的应用研究

在美军标MIL-STD-188-110B基础上,改进短波（HF）数据通信发送端数据流结构,以便接收端对信号进行盲均衡处理。基于8PSK调制信号的峰度为恒定值的统计特性,提出采用均衡输出信号的峰度与理想信号的峰度差异,以调整恒模算法（CMA）的步长因子;并针对国际电联推荐的短波信道参数,进行了算法的性能仿真。仿真分析表明该算法对慢衰落的短波信道具有较好的均衡效果,对快衰落信道的均衡能力有限;应对快速衰落信道,算法还有待进一步改进。     

N5B飞机机身钢构架焊接架数字化设计与制造技术

详细阐述了在N5B飞机机身钢构架焊接架的设计与制造中运用数字化技术的先进性。     

航空发动机管路流固耦合固有频率计算与分析

本文使用ANSYS有限元软件对航空发动机管路的流固耦合振动进行分析研究。讨论了管内流体质量、压力、温度,管路形状、截面尺寸对管路流固耦合固有频率的影响。最后,考虑上述所有影响因素,对一实际发动机燃油管路进行计算．得到了其固有频率和振型。     

某型飞机铝合金LY11螺旋桨腐蚀损伤试验

在疲劳试验机及电磁激振试验台上,对不同腐蚀情况的某型飞机螺旋桨桨叶模拟试件进行试验,分别得到了腐蚀损伤面积比随低周循环数N的变化规律,振动频率随损伤深度比、损伤长度比及损伤面积比的变化规律.试验表明,在载荷、温度相同条件下,材料性能、喷丸强化措施和使用环境是影响螺旋桨腐蚀损伤的重要因素;腐蚀损伤的面积比、腐蚀深度比对螺旋桨桨叶振动频率影响较大并获得最大深度比为0.14,模拟试件损伤深度最大允许值为0.7 mm,损伤面积比为0.015,损伤面积最大允许值为3.006 mm2.      

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

CZ2F火箭POGO振动信号特征频率提取

CZ2F运载火箭在第5次飞行过程中意外出现了"8Hz"POGO振动现象,该振动频率对箭体的稳定性和航天员安全产生了严重的影响。为解决这一振动问题,必须精确分析该频率的持续时间和振动量级。通过研究HHT(Hilbert-Huang Transform,希尔伯特-黄变换)方法,结合火箭振动信号特点设计了特征频率提取算法,成功地提取了CZ2F火箭飞行中的"8Hz"POGO振动频率,为有效解决"8 Hz"POGO振动问题提供了技术支撑。     

考虑陀螺效应的转子动力学相似准则

针对考虑陀螺力矩的转子系统缩尺相似模型与原型是否满足动力学相似的问题,采用量纲分析法推导了考虑陀螺力矩的转子-简单支撑系统相似准则,得到了模型与原型各物理量相似比.通过求解不同相似比下Jeffcott转子系统临界转速的解析解,和利用有限元软件ANSYS对某转子系统临界转速和振型相似性进行了数值模拟,验证了所推导的考虑陀螺力矩转子系统相似准则的正确性.研究表明:考虑陀螺力矩、简单支撑和Rayleigh比例阻尼的转子系统,在相似转速下缩尺模型与原型的固有频率具有相似性,并且临界转速相似.      

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

生产线仿真技术发展及在航空制造中的应用

生产线仿真技术作为实现数字化工厂的关键技术,预先对生产制造过程评估及解决瓶颈问题,近年来得到了越来越广泛的应用.阐述了生产线仿真的主要内容,回顾了生产线仿真技术的发展历程,分析了生产线仿真技术在航空制造领域的应用现状,最后指出生产线仿真技术在航空制造领域中进一步推广所需要解决的问题.     

IGS电离层产品在双向时间频率传递中的应用

利用IGS组织提供的全球电离层资料对卫星双向时间频率传递中的电离层误差进行修正。IGS提供特定时刻、固定经纬度网格点上的电离层总电子含量。对该电离层资料首先进行空间四点网格内插,然后利用双线性内插得到电离层穿刺点所需时刻的总电子含量,最后将得到电离层数据经过处理用于双向时间频率传递修正。结果表明：电离层对C波段的影响在（0～0.5）ns范围内,这对亚纳秒量级的时间比对是必须考虑的。IGS提供的电离层产品适合应用于双向时间频率传递,具有方法简单、准确度高和价格低廉等特点。