Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

周向总压畸变对对转压气机影响效应分析

以对转压气机为研究对象,在数值方法校验的基础上,应用全通道定常流场分析手段计算了对转压气机不同周向畸变条件下的三维流场,获取了周向总压进气畸变对该压气机性能以及流场结构的影响效应,确定了对转压气机的临界畸变角,分析了不同畸变强度对压气机性能的影响规律,探讨了周向总压畸变在对转压气机中的发展演化过程。结果表明:(a)所研究的对转压气机临界畸变角约为72°,略高于传统动-静叶排交替的压气机临界畸变角;(b)相比均匀进气工况,当畸变指数为0.24时,对转压气机失速点压比和失速裕度分别下降3%和9.6%,当畸变指数为0.5时二者分别下降8.3%和19.8%;(c)未畸变区与畸变区流体之间存在的压力梯度影响转子叶片相对来流速度。进入畸变区叶片来流相对速度减小,负荷降低,退出畸变区叶片来流相对速度增大,负荷增大;(d)上游转子使得畸变水平提高,下游转子反向旋转效应抑制了来流相对速度变化趋势,增强了气流在其叶片通道中的掺混,使得畸变水平有所下降。     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

Modeling of ionospheric parameter variations in East Asia during the moderate geomagnetic disturbances

The results of modeling of ionospheric disturbances observed in the East Asian region during moderate storms are presented. The numerical model for ionosphere–plasmasphere coupling developed at the ISTP SB RAS is used to interpret the data of observations at ionospheric stations located in the longitudinal sector of 90–130°E at latitudes from auroral zone to equator. There is obtained a reasonable agreement between measurements and modeling results for winter and equinox. In the summer ionosphere, at the background of high ionization by the solar EUV radiation in the quiet geomagnetic period the meridional thermospheric wind strongly impacts the electron concentration in the middle and auroral ionosphere. The consistent calculations of the thermospheric wind permit to obtain the model results which are closer to summer observations. The actual information about the space-time variations of thermosphere and magnetosphere parameters should be taken into account during storms.     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

一种用于飞机试验台的三分力传感器

多分力载荷传感器是一种常用的传感器,但通常当各分力的量程相差太大时难以取得良好的效果。提出了一种新型传感器结构形式,减少了各分力之间的耦合,使得在各分力量程不匹配的情况下亦可获得较高的测量精度。     

飞机飞行载荷测量载荷方程的优选

介绍用应变计方法测量飞机飞行载荷的载荷方程,应用方差分析和下检验技术进行优选,逐次剔除无应电桥和多余电桥,经自动计算,得到仅会对某种载荷有显著贡献的少量电桥的最优载荷方程,供飞行试验测量飞机飞行载荷使用。算例结果表明,此方法获得最优载荷方程有效。     

平均应变效应的循环粘塑性描述

提出了一个考虑具有平均应变循环变形行为的粘塑性本构模型,在该模型中,引入了可以计及平均应变效应的应变幅值记忆参数,构造了相应的背应力演化方程,定义了恰当的非比例度;还提出了对先前加载历史循环变形行为衰减记忆的各向同性变形阻力演化方程。模型用于１Ｃｒ１８Ｎｉ９Ｔｉ不锈钢的平均应变效应的本构描述,结果表明模型合理。     

基于立体视觉的板料成形极限应变测量关键技术及其系统

 设计并实现了一种基于双目立体视觉和数字图像相关方法的板料成形极限应变测量系统—BOSAS(双目视觉应变测量分析系统),对其中的关键技术作了深入讨论。该系统可以克服传统坐标网格方法很难进行变形过程的动态监控、自动化程度不高等局限,并可计算试件各变形阶段全场应变分布,以及重建不同变形时刻下试件的几何外形。将分段位移传递法和有限应变理论相结合,可计算大变形下的极限应变。对深冲铝板6016以及航空铝板2A12-T4、2A12-O、7B04-O等材料的应变测量结果显示本文方法适用于板料成形三维变形及极限应变的测量,并将测得数据与由坐标网格方法测得的数据进行比较,结果表明本文方法测量准确、可靠。     

结构动力特性分析中的圆角建模方法

针对薄壁结构中存在大量的圆角,提出了运用梁单元与壳单元组合的建模方法对圆角进行等效建模。通过分析圆角对薄壁结构的刚度贡献,提出圆角对结构刚度的贡献分为面内刚度贡献和面外刚度贡献。圆角对面外刚度的贡献与梁的作用等效,通过运用扭转相关理论推导出等效梁单元的截面参数。对于圆角的面内效应,运用壳单元对其进行等效建模,采用平面应变状态假设,将三维结构简化为二维结构。在平面内,通过刚度等效原理计算出壳单元的等效厚度与弹性模量。通过2个实例验证了圆角建模方法的正确性与准确性。