飞行器雷达罩设计方法的研究

详细分析了飞行器雷达罩设计过程中的基本问题。基于多目标优化设计方法建立了雷达罩结构参数求解的数学模型,给出了求解方法。考虑到雷达罩的安全使用要求,分析了雷达罩防雷击部件的基本要求,提出了设计方法,给出了防雷击部件布置的经验公式。同时还研究了用于飞行器雷达罩金属部件的吸波材料电磁波吸收机理,以及吸波材料电性能设计原理和基本布置准则     

风洞天平校准的因子法、正交法及单元校

本文证明瑞典航空研究院天平校准用的因子法与我国多元校用的正交法同属正交法。这不仅有助于正确认识这两种方法,而且对多元校实现自动加载会带来方便。从天平静校与风洞实验结果看,用单元校、因子法与正交法对天平校准将具有相同的准确度。本文提出载荷状态变化量并以其为标准来计算三种校准方法的加载量时发现,单元校的载荷状态变化量最少,因而其加载劳动量也最小。但是,单元校时必须重视对静校装置寄生分量的分析,而因子法与正交法则具有对静校装置寄生分量的平均效应。显然,本文的主要论点与国内一般看法不同且有新意,这将有助于对校准方法的研究,同时对静校装置的应用和设计都将会是有益的。     

Shock protection of penetrator-based instrumentation via a sublimation approach

It is often necessary for space-borne instrumentation to cope with substantial levels of shock acceleration both in the initial launch phase, as well as during entry, descent and landing in the case of planetary exploration. Current plans for a new generation of penetrator-based space missions will subject the associated on-board instrumentation to far greater levels of shock, and ways must therefore be found to either ruggedize or else protect any sensitive components during the impact phase. In this paper, we present an innovative method of shock protection that is suited for use in a number of planetary environments, based upon the temporary encapsulation of said components within a waxy solid which may then be sublimated to return the instrument back to its normal operation. We have tested this method experimentally using micromachined silicon suspensions under applied shock loads of up to 15,000g, and found that these were able to survive without incurring damage. Furthermore, quality factor measurements undertaken on these suspensions indicate that their mechanical performance remains unaffected by the encapsulation and subsequent sublimation process.     

浅析歼强飞机液压系统元件多发性故障

简要介绍歼强飞机液压系统的特点,论述元件多发性故障的现象、原因,列举动力元件、执行元件、控制元件和辅助元件常见故障分析和预防措施。     

蜂窝结构环形件的微型点焊

介绍了蜂窝环形构件微型点焊的电极、设备及工艺过程,分析了焊点质量,发现了条形蜂窝件的质量问题对点焊过程的影响,并提出了相应的解决措施。     

电网电压不平衡及谐波畸变时基波电压正负序分量分离新方法

针对传统锁相环(PLL)在电网电压不平衡及谐波畸变下利用常规软件锁相环不能准确获取相位的问题,提出了一种新的正负序分量分离新方法。利用了相序解耦谐振控制器能去除高次谐波和延时信号消除(DSC)法可滤除特定谐波的特性,将相序解耦谐振和延时信号消除法结合起来,达到更好的正负序分量分离的效果。最后,采用MATLAB/Simulink软件仿真结果证明了所提出方法的可行性和有效性。     

基于潜在成分和概率神经网络的时变结构系统的损伤识别

介绍了基于潜在成分(LC)分析和概率神经网络的损伤识别方法,并应用于一个实验室模型的损伤识别.结果表明,基于潜在成分(LC)分析和概率神经网络的损伤识别方法能在正常的时变质量情况下以较高的成功率对位于A或B处的某一损伤程度未知的损伤进行归类,为时变结构系统的定量损伤识别作出了有益的尝试.     

直升机某部件飞行状态的载荷分布特点研究

结合直升机的飞行载荷特点及使用要求,采用某型直升机动部件飞行测量载荷数据,经过“三峰谷点”雨流计数法统计处理,对飞行中实测到的183个飞行状态分别进行统计处理,假设检验及回归分析,确定了每个飞行状态的载荷分布类型及飞行状态的损伤,最后压缩归并成对直升机某动部件产生较大损伤的18种飞行状态,并提出了飞行状态中载荷的分布类型对直升机动部件的寿命有较大的影响。     

TiAl/IN718合金过渡液相连接

采用过渡液相TLP(Transient Liquid Phase)连接技术,以金属Ti,Cu,Ni箔构成复合焊料连接TiAl和IN718合金.研究了保温时间对接头界面结构的影响.实验结果表明:采用Ti-Cu,Ti-Ni复合焊料可以制备无缺陷的接头,但2种焊料形成液相的过程和机理不同.由于在等温凝固过程中,从IN718合金中扩散过来的合金元素可在焊缝区聚集,从而在接头中形成亚层结构.通过对接头焊缝区的组织分析和硬度测试表明,在实验条件下Ti-Ni焊料的等温凝固过程持续时间比Ti-Cu的短.     

Ionospheric Effects of Geomagnetic Storms in Different Longitude Sectors

This paper analyzes the state of the ionosphere during two geomagnetic storms of a different intensity evolving in different sectors of local time in different seasons. There were used the data from a network of ionospheric stations located in the opposite longitudinal sectors of 80°-150° E and 250°-310° E.This analysis has permitted us to conclude that the detected differences in the variations of the disturbances are likely to be determined by the local time difference of the geomagnetic storm development, its intensity and by the different illumination conditions of the ionosphere.