民用飞机复合材料C型框分析方法研究

以层压板理论为基础,提出一种复合材料C型框结构的工程分析方法,并通过试验给出了C型框结构设计许用值。通过工程分析结果与试验结果的对比,说明此工程分析方法可用于指导C型框结构设计。     

Love Waves in Layered Graded Composite Structures with Imperfectly Bonded Interface

Theoretical analysis and numerical calculations of Love wave propagation in layered graded composites with imperfectly bonded interface are described in this paper. On the basis of WKB method, the approximate analytic solutions for Love waves are obtained. By the interface shear spring model, the dispersion relations for Love waves in layered graded composite structures with rigid, slip, and imperfectly bonded interfaces are given, and the effects of the interface conditions on the phase velocities of Love waves in SiC/Al lay- ered graded composites are discussed. Numerical analysis shows that the phase velocity decreases when the defined flexibility parameter is greater. For the general imperfectly bonded interface, the phase velocity changes in the range of the velocities for the rigid and slip interface conditions.     

电磁超介质研究进展

电磁超介质是当前电磁学和物理研究领域中的前沿与热点，文章将左手材料、复合左／右手传输线、光子晶体统一在电磁超介质的体系下进行介绍，并论述了电磁超介质的发展现状。     

冲击滑动耦合作用下的材料磨损

研制了一种新型磨损试验机,用于研究材料在冲击滑动耦合作用下的磨损特性。试验机由电磁激振器激励悬臂梁产生法向冲击,电机带动旋转轴产生切向滑动。各试验参数（冲击力幅值、冲击力频率及滑动速度）调节方便可靠,最大冲击力、冲击频率及滑动速度分别为100Hz,200N及4．52m／s。本文使用该试验机对材料在冲击滑动耦合作用下的磨损特性进行了研究,并利用称重法、二维轮廓测量及电子扫描显微镜评估了材料磨损。结果表明：在相同试验条件下,试验的重现性较好,数据重复性误差小于7％。此外,硬度高的钛合金试件比硬度低的铝青铜试件磨损严重。     

用银河仿真机进行固体火箭姿态控制系统半实物仿真试验

本文介绍用YH-F_1仿真机进行固体火箭姿态控制系统半实物仿真试验的系统配置、仿真程序设计和仿真模型检验.     

Numerical Modeling of the Compression Process of Elastic Open-cell Foams

The random models of open-cell foams that can reflect the actual cell geometrical properties are constructed with the Voronoi technique. The compression process of elastic open-cell foams is simulated with the nonlinear calculation module of finite element analysis program. In order to get the general results applicable to this kind of materials, the dimensionless compressive stress is used and the stress-strain curves of foam models with different geometrical properties are obtained. Then, the influences of open-cell geometrical properties, including the shape of strut cross section, relative density and cell shape irregularity, on the compressive nonlinear mechani- cal performance are analyzed. In addition, the numerical results are compared with the predicted results of cubic staggering model. Numerical results indicate that the simulated results reflect the compressive process of foams quite well and the geometrical properties of cell have significant influences on the nonlinear mechanical behavior of foams.     

Cr12型钢检测分析及热加工技术

设计了一种计算机实时金相定量分析系统(简称:计算机分析系统),该系统采用先进的图像处理技术实现定量金相测量.利用该系统对Cr12型钢进行了定量金相分析,完成对模具失效形式的分析,并提出了解决模具寿命短的锻造方法.在保证锻件质量前提下,对锻后热处理工艺的主要特性和某些现象的可行性作了探讨性研究.提出了掌握Cr12型钢热加工关键技术是保证模具质量,提高模具寿命的主要途径.     

FL-24风洞埋入式进气道试验技术

采用中压引射和经过校准的文氏流量计的方法,有效提高了埋入式进气道的捕获流量和流量测量精度,成功地在FL-24风洞中建立了埋入式进气道试验技术.风洞试验表明:整个试验系统设计合理,流量测量精度达到了0.5%以内.     

神经网络在计算复合材料刚度退化中的应用

复合材料层合板的刚度退化相当复杂,并且是非线性的,目前缺乏足够的理论依据,很难按实际情况计算.本文从神经网络的角度出发,借助于神经网络的自适应性,通过对材料的实际载荷和实测应变值进行学习,使网络掌握其中各层的刚度变化规律.并且通过数值仿真和实验验证,证明此方法是完全可行的.     

Spin-stabilized satellite magnetic attitude control scheme without initial detumbling

The angular motion of an axisymmetrical satellite equipped with an active magnetic attitude control system is considered. The dynamics of the satellite are analytically studied on the whole control loop. The control loop is as follows: preliminary reorientation along with nutation damping, spinning about the axis of symmetry, then precise reorientation of the axis of symmetry in inertial space. Reorientation starts right after separation from the launch vehicle. Active magnetic attitude control system time-response with respect to its parameters is analyzed. It is proven that low-inclined orbit forces low control system time-response. Comparison with the common control scheme shows the time-response gain. Numerical analysis of the disturbances effect is carried out and good pointing accuracy is proved.