基于CFD/CSD耦合的叶轮机叶片失速颤振计算

为了研究叶轮机叶片的失速颤振特性,发展了一种计算流体力学与计算结构力学(CFD/CSD)时域耦合方法。该方法通过每一物理时刻CFD和CSD的循环迭代实现了耦合计算。在CFD分析中,采用鲁棒性较好的空间离散格式AUSM+-UP,并基于延迟脱体涡模型(DDES)模拟了带分离流动。在结构分析中,通过模态法构建了旋转叶片动力学方程并运用杂交多步方法进行求解。以孤立转子Rotor37为例,计算了不同工况下流场总体与细节参数,与实验结果的对比验证了CFD算法的精度。对某转子叶片进行了颤振特性研究,计算所得的广义位移时间响应曲线表明该叶片在近失速工况下会发生失速颤振,其表现形式为一阶弯曲模态发散且各阶模态之间不耦合。分析表明,流场不稳定和非定常效应是引起失速颤振的关键因素,同时折合频率的降低也会导致原本气动弹性稳定的叶片发生失速颤振。     

Computational engineering analysis of external geometrical modifications on MQ-1 unmanned combat aerial vehicle

This paper focuses on the effects of external geometrical modifications on the aerodynamic characteristics of the MQ-1 predator Unmanned Combat Aerial Vehicle (UCAV) using computational fluid dynamics. The investigations are performed for 16 flight conditions at an altitude of 7.6 km and at a constant speed of 56.32 m/s. Two models are analysed, namely the baseline model and the model with external geometrical modifications installed on it. Both the models are investigated for various angles of attack from −4° to 16°, angles of bank from 0° to 6° and angles of yaw from 0° to 4°. Due to the unavailability of any experimental (wind tunnel or flight test) data for this UCAV in the literature, a thorough verification of calculations process is presented to demonstrate confidence level in the numerical simulations. The analysis quantifies the loss of lift and increase in drag for the modified version of the MQ-1 predator UCAV along with the identification of stall conditions. Local improvement (in drag) of up to 96% has been obtained by relocating external modifications, whereas global drag force reduction of roughly 0.5% is observed. The effects of external geometrical modifications on the control surfaces indicate the blanking phenomenon and reduction in forces on the control surfaces that can reduce the aerodynamic performance of the UCAV.     

人机环境系统中CFD的研究

 采用ＣＦＤ技术对人机环境系统中的一个典型问题——飞机空调座舱的舒适性进行了数值模拟,建立了相应的数值模拟方法,扩展了原有算法。数值模拟的成功,充分展示了ＣＦＤ技术在人机环境系统中的作用与可能带来的效益。     

不同舵翼操纵面形式的水动力及艇后流场特性数值模拟研究

为研究共翼型舵和非共翼型舵两种操纵面形式的艇后流场特性及螺旋桨推进特性,基于SST(Menter)湍流模型建立了SUBOFF标准潜艇模型尾流场数值预报模型。经试验结果验证,所建立数值模型进行潜艇尾流场及螺旋桨推进性能预报具有较高精度。将SUBOFF潜艇模型的水平舵改进为共翼型舵及非共翼型舵,对艇后流场及水动力性能进行了预报。数值结果表明：在舵角小于10°时,共翼型舵使潜艇的俯仰力矩和垂向力相对非共翼型舵提升20%以上;在舵角超过10°时,共翼型舵的水动力优势随着舵角增大而减小。尾部流场预报显示：共翼型舵在小舵角时可以有效的消除舵翼结合处的涡流,同时共翼型舵可以有效的降低桨盘面伴流的不均匀性,对尾流品质的改善效果优于非共翼型舵。螺旋桨计算结果显示：共翼型舵螺旋桨推进系数在大部分舵角下都小于非共翼型舵,在舵角为20°时,共翼型舵相对非共翼型舵推力系数下降3.5%,扭矩系数下降2.4%;同时共翼型舵的桨盘面流场均匀度要优于非共翼型舵,舵角为5°时,共翼型舵桨盘面处流场不均匀度相对于非共翼型舵要降低7.1%,舵角为25°时则降低25.1%。     

Effect of scavenge port angles on flow distribution and performance of swirl-loop scavenging in 2-stroke aircraft diesel engine

Swirl-Loop Scavenging (SLS) improves the performance of 2-stroke aircraft diesel engine because the involved swirl may not only benefit the scavenging process, but also facilitate the fuel atomization and combustion. The arrangement of scavenge port angles greatly influences in-cylinder flow distribution and swirl intensity, as well as the performance of the SLS engine. However, the mechanism of the effect and visualization experiment are rarely mentioned in the literature. To further investigate the SLS, Particle Image Velocimetry (PIV) experiment and Computational Fluid Dynamics (CFD) simulation are adopted to obtain its swirl distribution characteristics, and the effect of port angles on scavenging performance is discussed based on engine fired cycle simulation. The results illustrate that Reynolds Stress Turbulence model is accurate enough for in-cylinder flow simulation. Tangential and axial velocity distribution of the flow, as well as the scavenging performance, are mainly determined by geometric scavenge port angles α_geom and β_geom. For reinforcement of scavenging on cross-sections and meridian planes, α_geom value of 27° and β_geom value of 60° are preferred, under which the scavenging efficiency reaches as high as 73.7%. Excessive swirl intensity has a negative effect on SLS performance, which should be controlled to a proper extent.     

可应用于民机空气动力设计中的数值优化方法

目前民机成功设计的一个关键要素即在设计中有效地引入计算流体力学（CFD）的模拟方法和软件,特别是具有设计能力的方法和工具。本文概要地叙述了反设计、基于CFD低可信度和高可信度模型等数值优化方法的发展和应用于民机设计的历史和现状;简单地介绍了即将举行的空气动力优化设计计算系列研讨会;重点讨论了对可应用于民机设计的基于Navier-Stokes方程解算器的OPTIMAS的数值优化方法的要求及其构造方法,并以翼身组合体整流外形和翼身融合体（BWB）外形的算例表明其有效性,说明OPTIMAS可以成为民机日常设计的方法和工具之一。     

高超声速飞行器后体/尾喷管优化设计

结合试验设计方法、替代模型技术和遗传算法构建一套改进的优化方法,并将其应用于高超声速飞行器后体/尾喷管的一体化设计.在构建优化方法时,针对替代模型采用渐近全局策略提高精度;针对遗传算法,采用实数编码、多目标定级排序和改进小生境技术.在后体/尾喷管的一体化设计应用中,结合高精度的计算流体力学(CFD,Computational Fluid Dynamics)求解,以两个设计点的推力和升力为目标,以力矩为约束,得到优化问题的Pareto最优前沿面,优化结果在综合性能方面有很大提升.该优化方法可进一步推广应用于更复杂的优化设计当中.      

洞映射方法的研究和改进

针对传统洞映射方法存储大的缺点,对"广义封闭"的概念进行扩展,提出了最小洞映射方法,该方法允许挖洞曲面结束于网格截断面,有效缩小了洞映射区域,节省了存储开销.对适用于广义封闭的洞映射单元识别方法进行了分析,指出了用物面信息判断映射单元属性可靠性较差.发展了一种新的特别适合广义封闭问题的识别方法:"Inverse mark",使用计算网格结点信息自动识别洞外单元,再作为初始点在网格内部推进.研究表明:"Inverse mark"方法计算效率高,可靠性好,自动化程度高,有效提高了重叠网格方法对缝隙等局部复杂结构的适应性     

过渡状态倾转旋翼气动力模拟的高效CFD方法

为显著减少倾转旋翼过渡飞行时气动力CFD模拟的计算代价,提出并建立了适合倾转旋翼过渡状态气动特性分析的高效混合CFD方法。首先,提出了适合于过渡状态模拟的嵌套网格系统,并发展了相应的挖洞和贡献单元搜寻方法。在此基础上,结合叶素理论和动量理论建立了旋翼气动力模拟的简化虚拟桨盘模拟方法(Virtual rotor model,VBM)。为了能够分析倾转旋翼气动力的细节特性,多层运动嵌套网格系统和单指令多数据流(Single program multiple data,SPMD)并行技术被引入来建立精确的旋翼模拟方法(Real blade model,RBM)。然后,通过将VBM和RBM方法结合,构建了适合倾转旋翼过渡状态气动特性分析的高效(Hybrid blade model,HBM)方法。最后,通过对有试验值对比的悬停状态典型旋翼和7A旋翼分别验证了VBM和RBM方法的有效性。分别采用3种方法预测了过渡状态不同倾转角下旋翼的气动特性,VBM表现出最优的计算效率,能用于倾转旋翼总体气动性能的分析。HBM方法在保证流场求解精度的基础上,相对于高精度的RBM方法节省了1/3的计算时间。