共轴式直升机旋翼气动干扰对航向操纵的影响

利用共轴式旋翼风洞实验结果，结合轻型共轴式直升机M16飞行中的现象，分析了上下旋翼气动干扰对共轴式直升机过渡飞行中航向操纵的影响。介绍了直升机由悬停转入垂直上升、平飞中加减速和转入爬升与下滑等过程中，由于上下旋翼干扰发生了变化，使直升机航向发生偏转后飞机的反应情况，以及在这种情况下应进行的相应操纵。所得结果对研究共轴式直升机的操稳特性有重要意义。     

空天飞机的边界层转捩

本文概述了边界层转捩对空天飞机性能的影响。在介绍确定边界层转捩起始点的线性稳定性理论和简单关联公式之后，又从噪声影响、头部钝头影响和钝锥飞行试验结果等几方面，讨论了线性稳定性理论的应用。接着介绍了采用转捩函数来确定转捩区的方法。从飞行试验、理论计算和风洞试验等三方面，探讨了进一步研究高超声速边界层转捩的途径。重点介绍了ＮＡＳＡＬａｎｇｌｅｙ研究中心的超声速、高超声速静风洞技术的发展。最后，对今后空天飞机边界层转捩的研究工作提出了建议。     

高超声速小钝锥尾流转捩规律与光电特性

显式有限差分方法用于求解小钝锥高超声速化学非平衡尾流的轴对称边界层方程。该方法既适用于层流也适用于湍流。应用 Goldburg 转捩准则确定转捩初始位置。详细地计算了小钝锥尺寸、飞行速度、高度对尾流转捩和光电特性的影响。从计算中得到转捩和光电特性变化的一些有用规律。对湍流亚密部分的雷达散射截面进行了规律性分析。计算结果具有实用参考价值。     

超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

后向台阶层流分离剪切层特性研究

应用激光测速仪对生向台阶层流边界层分离产生的剪切层在再附前的发展进行了测量，得到了时均速度、湍流强度及剪切层厚度等的分布特性，并研究了来流湍流度对台阶后流场湍强度分布及剪切层发展的影响，实验中发现台阶后有一个流速降低的区域，对此从涡动力学的角度作了解释。     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

Diurnal and seasonal variations in long-term changes in the E-layer critical frequency

Long-term changes in the E-layer critical frequency, foE, at three stations of the European region (Juliusruh, Slough and Rome) and also at Moscow and Wakkanai stations are analyzed by the method developed by the authors and described in detail in the previous papers. It is found that Juliusruh and Slough stations demonstrate a well-pronounced change in foE (a trend) during two previous decades. At the same time, the same features of the behavior of the aforementioned trend k(foE) are obtained. The trend is positive and negative in the morning and evening hours, respectively. Similar diurnal behavior of k(foE) is found also for Moscow station but with lower absolute values of the trends. A well-pronounced seasonal behavior of k(foE) is detected at Juliusruh and Slough: the trend is minimal and maximal in the summer period and at the end of fall—beginning of winter, respectively. The maximal amplitude in the morning hours reaches +0.04?MHz per year, whereas the minimal amplitude in evening hours is ?0.06?MHz per year. No systematic changes exceeding by the magnitude 0.01?MHz per year are found for Rome and Wakkanai stations. It is assumed that the observed trends are related to changes (trends) in the meridional wind bringing NO molecules from the auroral oval to lower latitudes.     

Laminar flow control research at TsAGI: Past and present

This paper presents a brief review of activities in laminar flow control being performed at the Central Aerohydrodynamic Institute named after Prof. N.E. Zhukovsky (TsAGI). These efforts are focused on the improvement of the existing laminar flow control methods and on the development of new ones. The investigations have demonstrated the effectiveness of aircraft surface laminarization applications with the aim of friction drag reduction. The opportunity of considerable delaying of laminar-turbulent transition due to special wing profile geometry and using boundary layer suction and surface cooling has been verified at sub- and supersonic speeds through various wind tunnel testing at TsAGI and during flying laboratory experiments at the Flight Research Institute (LII). The investigations on using hybrid laminar flow control systems for friction drag reduction were also carried out. New techniques of laminar flow control were proposed, in particular, the method of local heating of the wing leading edge, boundary layer laminarization by means of receptivity control, and electrohydrodynamic methods of boundary layer stability control.     

离散粗糙元诱发边界层转捩的实验研究

针对直升机转子叶片模型表面离散粗糙元诱发边界层转捩问题开展了实验研究,分析不同雷诺数下粗糙元尺寸参数对转捩位置的影响。实验在中航工业气动院直升机转子叶片模拟装置进行,在模型转子叶片表面布置不同尺寸的离散柱状粗糙元,利用红外热像技术探测边界层转捩,并提出一种基于湍流／层流区域面积比的转捩位置判定准则,目的是实现边界层转捩位置自动识别,进而分析粗糙元尺寸参数对转捩位置的影响。实验转速为300至600 r／m,对应叶尖切向速度为25～40 m／s。实现了对旋转叶片边界层转捩位置的定量测量,通过实验验证,转捩位置判定算法正确可靠,初步得到了不同高度 DRE 诱发转捩位置与雷诺数之间的关系,随着粗糙元高度的增加,转捩位置逐渐靠前。