弯曲纤维对SiO2f/SiO2复合材料拉伸强度的影响

以SiO_(2f)织物作为增强相,采用循环浸渍固化工艺,制备了SiO_(2f)/SiO_2复合材料。在制备过程中,通过对SiO_(2f)织物进行模压处理,使SiO_(2f)呈现出不同程度的弯曲,测定了纤维弯曲后复合材料的拉伸强度,研究了纤维弯曲时复合材料的断裂过程。结果表明:弯曲纤维将导致复合材料的拉伸强度下降,最低拉伸强度仅为5.5 MPa,纤维弯曲时复合材料的断裂过程为逐层断裂,断裂应变增加,最大断裂应变达到1.19%。     

Obtaining more accurate electron density profiles from bending angle with GPS occultation data: FORMOSAT-3/COSMIC constellation

Since 1995, with the first GPS occultation mission on board Low Earth Orbiter (LEO) GPS/MET, inversion techniques were being applied to GPS occultation data to retrieve accurate worldwide distributed refractivity profiles, i.e. electron density profiles in the case of Ionosphere. Important points to guarantee the accuracy is to take into account horizontal gradients and topside electron content above the LEO orbit. This allows improving the accuracy from 20% to 50%, depending on the conditions, latitude and epoch regarding to Solar cycle as reported in previous works.     

悬臂对称三角形板的弯曲

悬臂板的弯曲问题是平板理论中的难题之一,清华大学的张福范教授,自1979年以来,应用迭加的方法,获得了悬臂矩形板在均布、集中外载情况下弯曲问题的准确解。 本文应用三角级数的方法,获得了悬臂对称三角形板在均布外载条件下弯曲问题的准确解。     

各向异性矩形板横向弯曲一般解析解

采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。引入（Φｘ，Φｙ，Ｗ）＝∑∞－∞（ｉＡ，ｉＢ，Ｃ）ｅｉｍπξｅｉｍπηｒ（ｍ为整数，ｒ为控制方程特征根），并代入矩形板平衡方程组，推出实数型级数解，将其回代入平衡方程组中任两个，可确定待定系统（Ａ、Ｂ、Ｃ）之间关系。一般解析解还补充了厚板在ｘ、ｙ方向的梁函数。本文引入将三个平衡方程归并为一个６阶偏微分方程的方法给出问题特解。将一般解析解代入边界条件，用正弦数加角点条件的方法确定待求系数。数值计算表明本文求解是成功的。     

用弯剪法计算两向正交正放平板网架各杆内力

本文在节点法和截面法的基础上，将两者融为一体，为计算两向正交正放平板网架各杆内力，提供了一种新颖方法，称其为弯剪法，文中引用了实例，结果与其它方法完全一致，并符合实际，这就证实了本法的有效性和可靠性，有一定的参考价值。     

An improved procedure for manufacture of 3D tubes with springback concerned in flexible bending process

Three dimensional (3D) tubes, which possess the characteristics of space saving, lightweight and high strength, are widely used in many high-end industries such as aviation, aerospace, automobile and shipbuilding. However, when manufacturing a 3D tube in flexible bending process, springback is a big obstacle for improving the forming quality. In this paper, a new comprehensive strategy for springback control of 3D tubes is proposed. The strategy can be described as follows: (1) define the desired shape and manufacture shape; (2) optimize the manufacture shape using two tooling design methods (e.g. DA (displacement adjustment) method and B&T (bending and twisting) method presented in this paper); (3) make a discretization of the manufacture shape to acquire the optimized forming parameters. Additionally, experiment is implemented to validate the effectiveness of the new strategy. Results show that forming parameters acquired by the new strategy are partially effective. The new strategy also demonstrates that, during 3D tubes forming, the deviation caused by over-bent elements can be counteracted by the deficient-bent elements. This principle is helpful to reduce the difficulty of parameter determination in future.     

齿轮弯曲疲劳强度可靠性分析的新方法

以三参数可靠性分析模型为基础, 结合随机有限元法与齿轮的疲劳强度理论, 提出了一种计算齿根弯曲疲劳强度的新方法。该方法考虑了影响齿轮可靠性的随机因素, 如载荷、材料性能参数和刀具齿顶圆弧半径等, 从而使得全面、合乎实际地对齿轮疲劳强度的可靠性预测成为可能。计算分析表明, 刀具齿轮圆弧半径对齿轮弯曲疲劳强度可靠性的影响不能予以忽略。文中还讨论了其它随机因素以及齿轮的变位系数对齿轮可靠性的影响。      

复合材料层板弯曲问题优化设计

研究固定纤维指向，对称铺层复合材料层板在弯曲载荷作用下，以铺层厚度为设计变量，结构重量为目标函数，分别同时承受强度约束位移约束的约束的优化设计方法。     

各向异性简支斜形板弯曲解析研究

应用作者前期工作给出的各向异性斜板横向弯曲一般解析解对承受均布载荷的各向异性简支斜形极进行弯曲分析。讨论了各向异性、斜角β、各向异性θ对板挠度的影响。计算表明,对于各向异性菱形板的各向异性角关于对称时,板最大挠度相同,并在各向异性角为时菱形最大挠度取最小值,θ为0时菱形挠度为最大。     

两对边固定两对边自由矩形板的精确解

基于Ｋｉｒｃｈｈｏｆｆ薄板理论,提出双三角级数形式的挠度函数,求得两对边固定两对边自由矩形板的精确角,计算结果表明,这种解法收敛速度快,计算精度,易于工程应用。