Beam tracking method based on reconfigurable intelligent surface for obstructed communication

This paper proposes a new reconfigurable intelligent surface based three-dimensional beam tracking method to solve the beam tracking problems for the unmanned aerial vehicle with obstacles in communication channels. The proposed beam tracking method can not only regulate the reconfigurable intelligent surfaces to achieve the beam tracking of the obstructed communications, but also optimize the transmission efficiency of the communication. Firstly, a reconfigurable intelligent surface is proposed, which can correlate the transmission signals by adjusting the phase-shift matrix. Meanwhile, a new communication channel is constructed according to the reconfigurable intelligent surface, which consists of two parts. The first one is the channel between the unmanned aerial vehicle and the reconfigurable intelligent surface, the other is the channel between the reconfigurable intelligent surface and the ground base station. Note that the transmission performance of the communications can be optimized by adjusting the phase shift of each uniform linear array on the reconfigurable intelligent surface. Then, a new beam tracking method for the unmanned aerial vehicle with obstructed communications is proposed on the basis of the reconfigurable intelligent surface. By proposing the mixed genetic algorithm, the estimation accuracy of the azimuth and elevation angles is improved to enhance the performance of the beam tracking. Finally, the simulations are provided to verify the effectiveness of the proposed three-dimensional beam tracking method with reconfigurable intelligent surface.     

Sequential dynamic resource allocation in multi-beam satellite systems:A learning-based optimization method

Multi-beam antenna and beam hopping technologies are an effective solution for scarce satellite frequency resources. One of the primary challenges accompanying with Multi-Beam Satellites(MBS) is an efficient Dynamic Resource Allocation(DRA) strategy. This paper presents a learning-based Hybrid-Action Deep Q-Network(HADQN) algorithm to address the sequential decision-making optimization problem in DRA. By using a parameterized hybrid action space,HADQN makes it possible to schedule the beam patte...     

低功率霍尔推力器束流发散和推力矢量偏心特性研究

为了准确掌握不同工况下混合励磁模式低功率霍尔推力器束流发散和推力矢量偏心特性，凭借自主设计和改进的一套快速评估霍尔推力器束流发散角和推力矢量偏角原位集成诊断装置，系统研究了推力器在不同阳极质量流率、磁场、电场下束流分布和推力矢量偏心特性的变化规律。结果表明，束流发散角随阳极质量流率（0.65mg/s~0.95mg/s）和磁场强度（112Gs~142Gs）的变化呈现负相关的特性。当阳极质量流率0.95mg/s，束流发散角降到29.1°（＜30°）。推力矢量偏角随阳极质量流率和磁场强度的变化分别存在极大值（1.19°）和极小值（0.91°）。束流发散角、推力矢量偏角在250V~330V放电电压范围内基本保持不变。     

肋参数对液氧甲烷发动机推力室强化换热的影响

为深入研究带肋推力室强化传热的机理，对带肋液氧/甲烷推力室的燃烧与再生冷却进行了流动与传热耦合分析，并针对不同肋高和肋数目进行了参数化分析。结果表明:引入等效平均热流密度的概念可以准确描述带肋推力室中的实际传热过程;平均热流密度总是随着肋数目的增加而减小，当肋高恒定时，由于总换热面积增大，等效平均热流密度会随着肋数目的增加而增大;而当总表面积恒定时，等效平均热流密度会随肋数目的增加而减小。此外，盲目地增大总换热面积并不一定能改善传热强化，甚至会在某些情况下恶化传热，因此在设计过程中也应该结合其他肋参数进行综合考虑。     

Lift enhancement based on virtual aerodynamic shape using a dual synthetic jet actuator

The Dual Synthetic Jet Actuator (DSJA) is used to develop a new type of lift enhancement device based on circulation control, and to control the flow over the two-dimensional (2D) NACA0015 airfoil. The lift enhancement device is composed of a DSJA and a rounded trailing edge (Coanda surface). The two outlets of the DSJA eject two jets (Jet 1 and Jet 2). Jet 1 ejects from the upper trailing edge, which increases the circulation of airfoil with the help of the Coanda surface. Jet 2 ejects from the lower trailing edge, which acts as a virtual flap. The Reynolds number based on the airfoil chord length and free flow velocity is 250000. The results indicate that the circulation control method based on Dual Synthetic Jet (DSJ) has good performance in lift enhancement, whose control effect is closely related to momentum coefficient and reduced frequency. With the increase of the reduced frequency, the control effect of the lift enhancement is slightly reduced. As the momentum coefficient increases, the control effect becomes better. When the angle of attack is greater than 4°, the increments of lift coefficients under the control of DSJ are larger than those under the control of the steady blowing at a same momentum coefficient. The maximum lift augmentation efficiency can reach 47 when the momentum coefficient is 0.02, which is higher than the value in the case with steady blowing jet circulation control.