超声速膨胀角入射激波/湍流边界层干扰直接数值模拟

为了揭示膨胀效应对激波/湍流边界层干扰区内复杂流动现象的影响规律,采用直接数值模拟方法对来流马赫数2.9、30°激波角的入射激波与10°膨胀角湍流边界层相互作用问题进行了数值研究。系统地探讨了激波入射点分别位于膨胀角上游、膨胀角角点和膨胀角下游3种工况下膨胀角干扰区内若干基本流动现象,如分离泡、物面压力脉动及激波非定常运动、湍流边界层统计特性和相干结构动力学过程等。结果表明,激波入射点流向位置改变对分离区流向和法向尺度的影响显著,尤其是当激波入射点位于角点及其下游区域。研究发现,膨胀角干扰区内物面压力脉动强度急剧减小,分离区内压力波向下游传播速度将降低而在膨胀区内将升高,膨胀效应极大地抑制了分离激波的低频振荡运动。相较于入射激波与平板湍流边界层干扰,入射激波流向位置改变对膨胀角再附区速度剖面对数区及尾迹区影响显著,将导致其内层结构参数升高而外层降低,近壁区内将呈现远离一组元湍流状态的趋势。此外,流向速度脉动场本征正交分解分析指出,主模态空间结构集中在分离激波及剪切层根部附近而高阶模态以边界层内小尺度正负交替脉动结构为主。低阶重构流场结果表明,前者对应为分离泡低频膨胀/收缩过程而后者表征为分离泡高频脉动。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

基于RANS/LES混合方法的分离流动模拟

飞行器在大迎角、快速俯仰机动时,流场中含有大尺度、非定常的涡结构,传统雷诺平均Navier-Stokes （RANS）模型不能准确模拟流场结构,根据国际上相关研究的发展趋势,需要采用混合RANS/大涡模拟（LES）模型来对复杂分离流动进行准确模拟。本文对基于分区混合与湍流尺度混合的双重RANS/LES混合计算模型进行发展与应用。通过典型简化模型的静、动态湍流大分离流动,测试和验证所采用的脱体涡模拟（DES）类方法,重点研究改进的延迟DES （IDDES）模型在动态问题应用中的正确性和有效性,并对所采用的数值模拟方法和相应的计算软件的可靠性、鲁棒性以及精度进行了考核验证。典型算例包括超声速圆柱底部流动、跨声速方腔流动、NACA0015机翼深失速分离涡模拟等。计算表明：发展的IDDES类混合计算模型可有效解决对数层不匹配的问题;对于定态非定常分离流动,DES、DDES、IDDES等模型计算结果差别不大,随着流动的非定常特性增强,IDDES模型的优势逐渐显现;对于动态非定常分离流动,则需要采用IDDES类模型。     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

Mining Spatial Associations with Limited Sensory Information

Abstract

Human navigation in an unknown environment requires an understanding of the spatial relationships of the terrain. For example, a soldier who is on a reconnaissance mission in a new city needs to “know” the spatial layout of the surroundings with high confidence. Oftentimes, this understanding must be acquired within a very short amount of time and with limited sensory inputs. The soldier would benefit from a digital avatar that draws inferences about the spatial layout of the city based on an initial set of observations and guides the soldier either in further exploring the environment or in making decisions based on these inferences. In this paper, we present and evaluate an inductive approach to learning spatial associations using sensory data that is available from the simulation environment of a computer game, Unreal Tournament. We study two kinds of spatial relationships between nodes on a level of a game map: nodes that are placed near each other to satisfy some spatial requirement and nodes that are placed near each other to satisfy the design preferences of a level architect. We show that we can infer both kinds of relationships using an association rule mining algorithm. Furthermore, we show how to use an ontology to distinguish between these relationships in order to discover different types of spatial arrangements on a specific map. We discuss how the inferred associations can be used to control an avatar that makes recommendations for navigating unexplored areas on a map. We conclude with some thoughts on the applicability of our methods to scenarios in the real world, beyond the simulation environment of a game, and on how the learned associations can be represented and queried by a simple question-answer type system.     

基于ARM的移动机器人红外测距系统的设计

为实现机器人安全蔽障,设计了一种基于S3C2440A微控制器的红外测距系统,具体介绍了该测距系统的硬件结构、软件设计及其工作原理。S3C2440A内部具有8路模拟信号输入的10位ADC,将红外测距系统测得的模拟信号输入,通过A/D转换后输出。     

LabWindows/CVI环境下调用Word文档的实现方法

目的介绍一种在Labwindows/CVI环境下调用Word的实现方法;方法结合具体的实例,实现对Word文档的调用;结果该方法可以按照规定的格式自动生成Word文档;结论提高了软件的效率和自动化程度。     

某型教练机起落架信号电路改进设计

针对某型教练机存外场使用时出现起落架未放到位，而飞行员却没能及时发现的问题，本文对飞机起落架信号电路进行了分析，并提出了相应的改进措施。     

应用六西格玛提高钛合金超塑成形/扩散连接产品合格率

应用六西格玛提供的质量改进方法和统计分析工具,按照界定、测量、分析、改进、控制的步骤,运用Pareto图、因果图、过程能力分析、多元回归分析等多种工具,深入分析钛合金超塑成形/扩散连接产品制造过程中产生缺陷的根本原因并采取改进措施,有效提高了制造过程能力和产品合格率。