Finite element analysis of an inflatable torus considering air mass structural element

Inflatable structures, also known as gossamer structures, are at high boom in the current space technology due to their low mass and compact size comparing to the traditional spacecraft designing. Internal pressure becomes the major source of strength and rigidity, essentially stiffen the structure. However, inflatable space based membrane structure are at high risk to the vibration disturbance due to their low structural stiffness and material damping. Hence, the vibration modes of the structure should be known to a high degree of accuracy in order to provide better control authority. In the past, most of the studies conducted on the vibration analysis of gossamer structures used inaccurate or approximate theories in modeling the internal pressure. The toroidal shaped structure is one of the important key element in space application, helps to support the reflector in space application. This paper discusses the finite-element analysis of an inflated torus. The eigen-frequencies are obtained via three-dimensional small-strain elasticity theory, based on extremum energy principle. The two finite-element model (model-1 and model-2) have cases have been generated using a commercial finite-element package. The structure model-1 with shell element and model-2 with the combination of the mass of enclosed fluid (air) added to the shell elements have been taken for the study. The model-1 is computed with present analytical approach to understand the convergence rate and the accuracy. The convergence study is made available for the symmetric modes and anti-symmetric modes about the centroidal-axis plane, meeting the eigen-frequencies of an inflatable torus with the circular cross section. The structural model-2 is introduced with air mass element and analyzed its eigen-frequency with different aspect ratio and mode shape response using in-plane and out-plane loading condition are studied.     

基于中值滤波和参考点的风洞压敏涂料试验图像处理技术

提出了一种结合图像中值滤波和试件参考点的风洞压敏涂料（PSP）试验图像数据处理方法。与通常用校准箱获取校准曲线进而得到PSP试验试件表面压力或压力系数（Cp）的方法不同，该方法通过空心中值滤波技术恢复PSP光强比图像中测压孔处的光强比数据，结合若干参考点处常规测压技术实测所得Cp值，获得Cp值和PSP图像光强比数据的关系曲线，进而得到整个试件表面的Cp值数据，该方法获得的数据结合了风洞试验诸多因素对试验结果的影响。利用MATLAB对PSP技术试验图像数据进行了处理，并将PSP方法获得的Cp值与常规测压方法获得的Cp值进行了比较，得到的结果显示，笔者采用的方法获得的Cp值与常规测压方法获得的Cp值吻合较好。该方法为PSP图像数据的处理提供了一种新的方法，具有较大的发展潜力和应用价值。     

二维活塞航空燃油泵容积效率分析

提出了一种二维活塞燃油泵，该泵利用二维活塞的旋转运动将配流机构集成到活塞上，去除了传统柱塞泵独立的配流机构，简化了泵的结构、提升了泵的功率密度，而且由于主要运动机构采用了滚动轴承支撑，免除了滑动摩擦副及其产生的泄漏，提高了效率。对泵的容积效率进行理论分析和实验研究。结合泵的结构原理分析了造成容积损失的内泄、外泄及油液压缩性等3种主要原因；应用层流和紊流的缝隙流动基本理论推导出泄漏解析表达式，着重分析了不同配流开口形式产生的内泄漏；综合考虑油液压缩性和泄漏获得了容积效率数学模型。理论研究表明采用负开口配流形式可以有效减小内泄漏，定量分析了泄漏流量与负开口量的关系，同时利用Fluent进行配流过程中泵腔内的流场数值模拟，结果表明可以有效减小油液倒灌。为了验证理论分析的有效性，制作二维活塞燃油泵样机，以航空煤油为介质进行台架实验。样机实验结果表明在负载压力2 MPa，转速从1 000 r/min到5 000 r/min，容积效率从93.6%提升到98.1%；当转速为2 000 r/min，负载压力从1 MPa增大到5 MPa，容积效率从97.5%降低到92.3%。以现有的齿轮泵和柱塞泵相比容积效率显著提高，理论与实验的结果偏差在4%以内，表明理论分析的有效性和正确性。     

尾迹对涡轮动叶全表面气膜冷却效率的影响

采用压敏漆（PSP）测量技术研究了尾迹对涡轮动叶气膜冷却效率的影响，测试叶片带有11排圆柱形气膜孔。获得了不同质量流量比和尾迹斯特劳哈尔数（Sr=0，0.12，0.36）条件下全表面气膜冷却效率分布的试验数据，结果表明：随着尾迹Sr数的增加，叶片前缘区域径向平均气膜冷却效率最大降低幅度达36.5%，吸力面径向平均气膜冷却效率最大降低幅度达53.5%，压力面径向平均气膜冷却效率最大降低幅度达24.2%；尾迹对前缘和吸力面气膜冷却效率的影响大于压力面；随着质量流量比增加，尾迹的影响减小；在进行涡轮动叶表面气膜冷却结构设计时，不考虑尾迹效应会增加设计风险。     

Numerical investigation on hydrogen combustion in a scramjet with 3D sidewall compression inlet

Numerical simulations were employed to analyze the flowfield of a scramjet with three-dimensional (3D) sidewall compression inlet, and the effect of inlet distortion on the mixing and combustion process was examined. The numerical approach solved the compressible Reynolds Averaged Navier–Stokes (RANS) equations supplemented with a finite rate chemical reacting model for the combustion of hydrogen fuel and air. Turbulence closure was achieved using Menter shear-stress transport (SST) model. To verify the accuracy of the simulation, the computed wall pressure was compared with the experimental data of the direct-connect combustor test. The metrics employed in the simulations included qualitative assessments related to flow structure as well as quantitative values of fuel mixing efficiency, combustion efficiency and static pressure distribution. Intake sidewalls were found to strongly affect the inlet flow structure, which became more complex in the nonuniform flowfield. The shock train system affected the combustion region located upstream of the injection and led to pairs of asymmetric separation bubbles. Nevertheless, the shock train system dissipated due to the reactions, the combustion patterns of each fuel jets in downstream region were nearly identical, and the degree of improvement of mixing and combustion efficiency near the downstream injectors was less than that near the upstream injectors.     

带中心支板侧压进气道流场特性研究

应用表面油流和压力测量实验技术,辅助计算模拟手段,考察了两种不同形式的中心支板对侧压式进气道流场特性的影响.结果表明:进气道内部由于侧壁斜激波和支板诱发的斜激波的汇合引起了侧壁和顶板边界层的大尺度分离现象,使进气道性能受到了极大影响.后掠支板后移避免了支板和侧壁诱导斜激波的汇合,分离现象相对较弱,有利于进气道性能的提高;支板前掠可以提高流量捕获,但导致边界层分离加剧,对减少总压损失不利.     

预混气爆震波在不同直径管间的传播特性

在管径20mm与60mm的两管间研究了预混气爆震波的传播特性,着重测量了爆震波传递过程中的压力与速度变化,并分析了预混气压力、浓度、当量比以及连接段尺寸等参数对爆震波传播的影响与规律。研究发现:小管中没有爆震时大管中仍然可以出现爆震波,小张角的连接段对爆震波的再触发有利,再触发后的爆震波其压力、速度受到预混气压力、浓度及当量比等参数的影响。      

带60°肋U型通道中气膜孔对通道换热特性的影响

以航空发动机涡轮叶片中段内部冷却通道为研究对象,将其简化为带肋变截面U型通道。对通道内有气膜出流时的换热特性进行了实验研究。实验模型中,矩形肋对称布置在上下2个表面,气膜孔仅布置在第2通道内。文中定义了气膜开孔率的概念,采用单元分析法研究了气膜开孔率和出流比对通道内单元努塞数分布和第2通道压力分布的影响。实验结果表明,气膜出流比一定时,随着开孔率的增加,换热增强;在两肋之间的3个气膜孔中,肋后孔对通道换热影响最大;气膜出流比与通道努塞数的关系为二次曲线。      

陀螺静态漂移系数的两种估计方法

在分析了目前使用的AR（1）估计方法之不足后，提出了均值估计方法，以及这两种方法的改进型，即加权均值估计法和AR（p)法，计算结果表明，均值估计可以提高精度近40％，在导弹发射前的陀螺误差补偿中使用这一方法效果会更好。     

合成孔径雷达方程

导出适用于合成孔径雷达（SAR）的基本方程，用于决定回波信号功率、检测前后的信噪比、平均发射功率和噪声等效后向散射系数。考虑了地物目标特性、信号相干积累和多视处理效应，并对各种参数的影响进行讨论。