提高某铝合金薄壁深孔零件加工质量研究

通过分析某铝合金薄壁深孔零件在加工过程中存在的问题基础上,采用了拉镗拉铰加工内孔,再以轴向定位夹紧的方式加工外形的思路,该方法保证了零件加工精度,解决了该铝合金薄壁深孔零件的加工问题,完全满足生产实际需要,质量稳定可靠,可为类似零件加工提供参考。     

航空用铝合金在酸性盐雾环境中腐蚀电化学

用失重法和电化学方法研究2A12,5A06和7A04铝合金在中性和酸性(pH≈5)连续盐雾环境下的腐蚀过程。通过金相显微镜和接触角表面分析仪观察其金属相界面处的腐蚀形貌和表面状态,分析腐蚀机理。结果表明:失重法、极化曲线Tafel外推法和电化学阻抗谱法均显示3种铝合金在中性盐雾中腐蚀速率的大小关系为7A042A125A06;在酸性盐雾中腐蚀速率的大小关系为7A045A062A12;铝合金表面与中性和酸性盐溶液的接触角分别为70.9°和52.6°,酸性盐溶液的接触角小于中性盐溶液的接触角,可能是因为氢离子增多使阴极反应右移,加速阳极溶解,破坏了铝合金表面的氧化膜。     

Ti-22Al-25Nb合金剪切旋压过程中显微组织演化

通过剪切旋压试验,研究了旋压温度(910℃和1000℃)和减薄率(0、10%和30%)对Ti-22Al-25Nb合金显微组织的影响,探讨了旋压过程中的显微组织演化规律。结果表明:Ti-22Al-25Nb(原子数分数)合金旋压组织主要由α2相、B2相和O相组成,在旋压过程中,B2晶粒沿旋轮进给方向被拉长,且伴随有动态再结晶现象发生;温度主要影响Ti-22Al-25Nb合金中α2相与O相的尺寸和形貌,随着旋压温度的升高,O相片层逐渐变短并粗化,α2相趋向等轴化;变形量主要影响α2相体积分数与O相形貌,随着减薄率的增大,α2相体积分数逐渐减少,O相从片层状转变为短棒状。因此,Ti-22Al-25Nb合金剪切旋压过程中不仅发生晶粒变形与动态再结晶现象,更涉及复杂的相变行为,组织控制困难。     

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

基于改进Johnson-Cook模型的5083P-0铝合金动态本构关系研究

为研究5083P-0铝合金在高应变率下的力学行为及本构模型,通过RPL100材料试验机和分离式霍普金森压杆(SHPB),对5083P-0铝合金进行了准静态及应变率范围950～3000 s-1的冲击动态压缩实验.结果 显示随着应变率的增加,5083P-0铝合金的屈服强度、流动应力增加,应变硬化率减小,具有应变硬化效应,正...     

5005铝合金分流模挤压过程有限元模拟

采用DEFORM-3D有限元商业软件,利用焊合面重构技术实现了空心型材分流组合模挤压过程模拟,获取了挤压过程中的材料流动行为与流动速度场的规律,结合型材挤出时模拟的应力场和应变场的分布,研究型材挤压的晶粒分布规律并其成因。结果表明:挤压型材的横截面上的应力应变分布与实际晶粒尺寸分布有对应关系,型材挤压成形过程中应力应变集中分布是造成型材边部晶粒尺寸比中心部细小,拐角区域晶粒比直边区域细小的原因。     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

储氢合金的性质及发展趋势

本文介绍了储氢合金的性质，Ｎｉ－ＭＨ电池原理，以及储氢合金对Ｎｉ－ＭＨ电池所产生的影响，根据目前科学技术的发展以及市场的需求，提出了未来储氢合金及Ｎｉ－ＭＨ电池的发展趋势。     

气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。     

结构比强度及其在优化设计中的应用

本文从结构重量角度推导了比强度(含比模量)表达式,分析了对同一材料不同比强度的关系,给出了比强度在结构动态分析中及结构优化设计中的应用。