推力向量控制方案及计算

本文归纳推力向量控制的主要方案,着重介绍摆动喷管、流体二次喷射方案的计算思路和结果.摆动喷管中的流场计算要考虑导弹偏摆对所产生的惯性力的影响;所得壁面压力畸变图说明,它是一个三维流场.在摆动喷管设计中要将铰链力减至最小,流体二次喷射的侧向力通过“等效实体模型”,用爆炸波的解来计算.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

一种基于工程化气动加热算法的天线热防护设计

高超音速气动热仿真技术是提高天线热防护能力的重要支撑之一,为了进一步缩短研制周期和节约成本,本文提出了一种以冷壁热流和壁面恢复焓为输入条件,以MATLAB和CFD联合迭代快速求解高速气流中天线温度场的工程化算法。在利用气动热试验证明仿真结果与实验数据的高一致性后,以该仿真方法对一个高速气动加热时长为500 s的天线实施了防隔热优化设计,根据仿真评估出的导致核心器件温升的主、次要因素,针对性地提出改进措施,最终目标印制板由过往的320℃下降到了142℃,热控效果显著。     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).     

风挡串流对测力数据的影响及其改进措施

本文研究了风挡串流对三角形机翼飞机模型测力数据的影响。试验结果指出,在风挡具有串流的情况下,正反装模型所获得的纵向测力数据都是错误的,特別是俯仰力矩。为了消除风挡串流对测力数据的影响,应尽力限制串流量,此外建议在测定模型的平均气流偏角和支架干扰量时,上风挡亦带串流,并使其对称于下风挡的串流。经试验证明,这些措施将有助于获得较为可靠的正反装测力数据。     

转子叶片加工误差对1.5级跨声速压气机气动性能的影响

压气机叶片加工误差不可避免,将在一定程度上影响压气机的气动性能.为研究叶片加工误差对跨声速压气机气动性能的影响,以燃气轮机进口1.5级跨声速压气机为对象,通过三坐标测量跨声速转子叶片叶型数据,获得了加工误差分布特征;针对实测转子叶片,采用三维CFD数值模拟方法,研究了轮廓度、位置度和扭转角综合误差对压气机转子和级特性线...     

短螺旋型燃烧室旋流结构及气动边界发展规律数值模拟研究

短螺旋型燃烧室的头部轴线沿发动机周向与发动机轴线偏转一定角度,可以在保证燃烧效率不变的条件下有效缩短燃烧室轴向长度。短螺旋型燃烧室流场的最大特点是旋流流动单侧受限。为了研究头部安装角α变化对燃烧室旋流流动特性的影响,基于数值方法对短螺旋型燃烧室进行了计算分析。结果表明:随着α变化,旋流器下游旋涡依次出现对称环状、马蹄状、环状结构;随着α增加,气动边界逐渐出现并抑制旋流的周向扩张,导致流场出现不同的旋涡结构;不同α下的切向角动量随轴向距离增加而衰减,但α为35°和45°时,气动边界在非受限侧出现并对旋流产生约束,角动量衰减变慢;当α为0°,15°,35°,45°时,燃油液滴依次集中分布在旋流器下游两旋涡边缘、侧壁面和头部端壁、非受限旋涡边缘。本文研究了不同α下的旋涡结构及气动边界沿轴向的演化过程,为短螺旋型燃烧室进一步的设计与优化提供基础。