高速圆柱滚子轴承保持架动力学特性分析

建立了高速圆柱滚子轴承动力学微分方程,采用精细积分法和预估-校正Adams-Bashforth-Moulton多步法相结合的算法,对高速圆柱滚子轴承动力学微分方程进行求解,并对保持架的动力学特性进行了理论分析.结果表明:过大的保持架间隙比不利于保持架稳定运转;在一个套圈固定、另一个套圈工作状态下,保持架引导方式采用旋转套圈引导时,保持架打滑率较低;保持架采用外引导方式时保持架质心运动较为稳定;在内外圈同向旋转且外圈转速高于内圈转速条件下,保持架采用外引导方式时,保持架打滑率较低;在内外圈反向旋转且外圈转速高于内圈转速条件下,保持架质心轨迹变得不规则;保持架采用外引导方式时,保持架打滑率为负值.      

改进的Qiu滑移因子模型用于离心压气机叶轮的参数研究

为适用于微型离心压气机叶轮的通流设计,对Qiu滑移因子模型加入了3个经验参数.首先对经验参数的求解方法及参数对于设计精度的影响进行了分析研究,发现其中经验参数c_r对于设计精度影响较大.其次在通流设计中应用改进的Qiu滑移因子模型辅助生成叶片,用计算流体动力学(CFD)研究了c_r所影响的模型滑移因子,与数值流场的出口平均滑移因子对比,得到了多种叶轮总体参数下c_r的最佳取值.发现虽然微型、大型离心压气机叶轮总体参数变化范围很大,但c_r的取值均以0.7左右为其最佳值.      

双级波瓣引射混合器的引射性能

采用实验和数值方法对双级波瓣引射混合器的引射性能进行研究,重点研究混合管在两种不同进口方式下的引射混合器气动特征差异,并初步分析混合管面积比和长径比对双级波瓣引射混合器引射性能的影响.结果表明:混合管进口方式对引射能力有非常重要的影响,在研究的结构参数条件下,对于受限式进口,单级波瓣引射混合器的引射能力要强于双级波瓣引射混合器约10%;而对于敞开式进口,其引射能力要优于受限式进口最大约35%,此时双级波瓣引射混合器的引射能力要略好于单级波瓣引射混合器.在较大的混合管面积比或较小的长径比下,敞开式进口下双级波瓣引射混合器较受限式进口表现尤为优越.      

加力燃油计量装置的AMESim 仿真研究

为获得加力燃油系统数字化仿真与性能验证平台,采用功能划分的方法分析了典型计量装置的功能模块,确定了伺服阀-随动活塞、计量活门-等压差活门是决定计量装置动态特性的主要组成部分,对其进行了数学建模。鉴于获得的数学模型描述系统特性时缺乏相关元件特性参数的设计依据,建立了由计量活门、等压差活门、电液伺服单元等组成计量装置的AMESim模型,计算主要结构参数后仿真分析了其稳态和动态特性。结果表明:基于控制系统构成的加力燃油计量装置功能划分与数学建模可为仿真研究与参数设计提供指导,AMESim可用于动态过程仿真与性能预测。     

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

一种基于光固化快速成型的飞机静弹性风洞试验模型设计方法

高速风洞静弹性模型设计和制造是静弹性风洞试验的一个关键。为解决模型设计周期长、制造费用高等问题,提出了一种基于立体光固化快速成型面向高速风洞大展弦比机翼静弹性模型研制方法。基于机翼刚度分布相似参数,采用机翼钢梁骨架和树脂蒙皮组合结构,通过优化结构尺寸完成静弹性模型结构设计;使用机械加工和快速成型技术完成模型制造,并通过地面刚度试验对加工模型进行了刚度分布验证。风洞试验结果表明：基于立体光固化成型技术设计和制造的静弹性风洞试验模型工程实用、可行,与传统静弹性模型研制过程相比,具有研制周期短、成本低而且不存在因填充物带来附加刚度的显著优势。     

C频段宽带线／圆极化器小型化设计

为适应C频段卫星测控通信车栽天线机动布站功能,须研制一种轴向尺寸小于1．2m的小型化天馈系统,针对该问题,对关键组件线／圆极化器进行小型化设计。在理论分析极化器原理的基础上,采用在聚四氟乙烯基材上打孔的方法使一种介质实现多种相对介电常数,设计了C频段收、发均覆盖575MHz带宽的小型化宽带极化器,在56％相对带宽内实现小型化,轴向尺寸缩短至常规极化器的1／a,经HFSS（HighFrequencySimulationSoftware,高频仿真软件）仿真计算,并与同频段常规极化器性能进行分析比较,结果表明：该极化器移相量与匹配性能良好,满足指标与使用要求。     

An extrapolation approach for aeroengine’s transient control law design

Transient control law ensures that the aeroengine transits to the command operating state rapidly and reliably. Most of the existing approaches for transient control law design have complicated principle and arithmetic. As a result, those approaches are not convenient for application. This paper proposes an extrapolation approach based on the set-point parameters to construct the transient control law, which has a good practicability. In this approach, the transient main fuel control law for acceleration and deceleration process is designed based on the main fuel flow on steady operating state. In order to analyze the designing feature of the extrapolation approach, the simulation results of several different transient control laws designed by the same approach are compared together. The analysis indicates that the aeroengine has a good performance in the transient process and the designing feature of the extrapolation approach conforms to the elements of the turbofan aeroengine.     

读来读往

CIMT将于4月22日在北京隆重开幕。面对后危机时代的挑战,中国已连续几年成为世界第一大机床消费国,本届展会更是盛况空前,代表世界顶尖技术水平的机床工具产品将大放异彩。本刊为此推出了"未来机床"、"未来刀具"、"未来测量"和"未来工厂"4期特别策划。本期是以"未来工厂"为主题的特别策划。封面文章介绍了数字化工厂技术的应用现状与趋势;专稿针对实现飞机全三维设计的