Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

无线电高度表信号模拟器射频信号延时/衰减模块设计

无线电高度表程控信号模拟器是无线电高度表自动测试系统（ATE,ATS）的重要组成部分,而射频信号延时/衰减模块则是无线电高度表程控信号模拟器3个功能模块组件中的核心模块。研制了一种采用声表面波（SAW）延迟线作为射频信号延时器件、射频衰减器作为射频信号功率衰减器件,通过程控射频开关控制不同声表面波延迟线的切换,包含射频信号变频、放大等结构电路的无线电高度表信号模拟器射频信号延时/衰减模块。经无线电高度表自动测试系统的实际工程应用表明,该无线电高度表射频信号延时/衰减模块对C波段（4.2～4.4 GHz）射频调制信号的延时精度高、衰减范围大,体小、质轻,适合置于无线电高度表测试适配器内部使用,具有较高的工程应用价值。     

基于EFFD方法的自然层流短舱优化设计

采用extended free-form deformation(EFFD)方法研究了自然层流(natural laminar flow,NLF)短舱的气动外形优化设计方法.使用基于Bernstein基函数的EFFD方法完成了NLF短舱剖面的参数化,利用基于k-εSST(shear stress transport)两方程湍流模型的γ-θ转捩模型进行自然转捩预测,结合EFFD、一种混合动网格方法、Kriging代理模型和改进的粒子群算法(particle swarm optimization,PSO)建立了针对NLF短舱气动外形的优化设计框架.采用该框架分别对通气NLF短舱和带动力NLF短舱进行优化设计.单独通气NLF短舱优化结果的外表面实现48%的层流,阻力系数比初始通气NLF短舱减小了0.0003.带动力NLF短舱的优化结果外表面保持了41%的层流.这些结果表明采用相关技术建立的优化设计框架在NLF短舱设计中具有一定应用价值.     

X射线脉冲星导航硬件脉冲轮廓累积研究

为了在X射线脉冲星地面实验系统仿真源模拟产生X射线的基础上,能够快速稳定地得到脉冲轮廓,采用硬件历元叠加的方法获得脉冲轮廓。研究了用硬件实现历元叠加及其数据整合的算法,该算法首先在MATLAB现场可编程逻辑阵列(FPGA)中实现,再通过MATLAB硬件描述语言(HDL)代码生成模块把算法转换成HDL,经编译后获得配置硬件的Bit文件,最终在开发板FPGA上实现数据处理的硬件模块。一段时间内的光子到达时间数据通过MATLAB算法得到的脉冲轮廓数据与通过硬件模块处理后得到的数据结果存在误差,在单个时间窗口内误差最大值为2个光子数,误差平均值占光子数统计平均值的0.084%;两组统计的脉冲轮廓数据中不同数据占总数据个数的9.481%,这样的误差不影响后端模拟导航模块的导航。利用硬件实现的历元叠加及其数据整合模块具有处理速度快、设备紧凑、功耗低的特点,为航天器利用X射线脉冲星导航提供了一种可行的硬件数据处理技术上的支持。     

存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

太空原位制造和修复技术研究现状分析

概述了太空原位制造和修复技术（In—situ Fabrication and Repair,ISFR）的概念和特点,并结合该技术的发展背景,介绍了国内外以选择性激光烧结和电子束熔融技术为代表的太空原位制造、空间钎焊修复、太空基地建筑构建等方向发展现状及趋势。结合我国空间技术事业发展,提出充分借鉴国外相关技术成果,围绕主要应用材料,重点开展空间环境适应性和应用验证研究,并探索利用模拟月壤开展太空原位制造技术研究的设想与建议。     

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.