全文获取类型
收费全文 | 337篇 |
免费 | 32篇 |
国内免费 | 12篇 |
专业分类
航空 | 210篇 |
航天技术 | 42篇 |
综合类 | 21篇 |
航天 | 108篇 |
出版年
2024年 | 3篇 |
2023年 | 14篇 |
2022年 | 9篇 |
2021年 | 11篇 |
2020年 | 7篇 |
2019年 | 11篇 |
2018年 | 1篇 |
2017年 | 7篇 |
2016年 | 13篇 |
2015年 | 7篇 |
2014年 | 13篇 |
2013年 | 15篇 |
2012年 | 15篇 |
2011年 | 8篇 |
2010年 | 8篇 |
2009年 | 13篇 |
2008年 | 32篇 |
2007年 | 22篇 |
2006年 | 13篇 |
2005年 | 20篇 |
2004年 | 21篇 |
2003年 | 14篇 |
2002年 | 12篇 |
2001年 | 20篇 |
2000年 | 8篇 |
1999年 | 8篇 |
1998年 | 7篇 |
1997年 | 13篇 |
1996年 | 7篇 |
1995年 | 1篇 |
1994年 | 5篇 |
1993年 | 7篇 |
1992年 | 5篇 |
1991年 | 5篇 |
1990年 | 2篇 |
1989年 | 3篇 |
1988年 | 1篇 |
排序方式: 共有381条查询结果,搜索用时 31 毫秒
11.
为了在X射线脉冲星地面实验系统仿真源模拟产生X射线的基础上,能够快速稳定地得到脉冲轮廓,采用硬件历元叠加的方法获得脉冲轮廓。研究了用硬件实现历元叠加及其数据整合的算法,该算法首先在MATLAB现场可编程逻辑阵列(FPGA)中实现,再通过MATLAB硬件描述语言(HDL)代码生成模块把算法转换成HDL,经编译后获得配置硬件的Bit文件,最终在开发板FPGA上实现数据处理的硬件模块。一段时间内的光子到达时间数据通过MATLAB算法得到的脉冲轮廓数据与通过硬件模块处理后得到的数据结果存在误差,在单个时间窗口内误差最大值为2个光子数,误差平均值占光子数统计平均值的0.084%;两组统计的脉冲轮廓数据中不同数据占总数据个数的9.481%,这样的误差不影响后端模拟导航模块的导航。利用硬件实现的历元叠加及其数据整合模块具有处理速度快、设备紧凑、功耗低的特点,为航天器利用X射线脉冲星导航提供了一种可行的硬件数据处理技术上的支持。 相似文献
12.
13.
航空发动机闭环控制系统的设计过程复杂且环节繁多,如果通过某平台综合多个设计过程,必然可以简化流程,提高效率.在总结国内外相关文献的基础上,针对民用涡扇发动机,在Matlab/Simulink下,利用模块化方法构建包含稳态控制器、过渡态控制器以及极限保护器的涡扇发动机闭环控制系统仿真平台,并对其进行仿真测试和硬件在回路实验.结果表明,所构建的仿真平台满足控制系统的性能和实时性要求,具有良好的工程适用性. 相似文献
14.
15.
针对电离层周日变化特征分析了其可能对SCORE方法估算的硬件延迟稳定性的影响. 利用BJFS以及XIAM台站的GPS观测数据, 解算了位于太阳活动高年(2001年)和太阳活动低年(2009年)的卫星硬件延迟并分析了估算的硬件延迟的稳定性. 研究发现, 电离层周日变化对估算的硬件延迟稳定性具有一定影响, 但是利用不同台站所得到的卫星硬件延迟稳定性在昼夜不同时间上的解算结果存在一定差异. 电离层周日变化对利用 BJFS台站数据解算的硬件延迟稳定性日夜差异较为明显, 在太阳活动高年利用XIAM 台站数据解算的硬件延迟日夜稳定性差异不很明显, 由于XIAM台站处于电离层赤道异常峰附近, 夜间电离层变化很大, 因此对比中纬度地区, 电离层周日变化对赤道异常峰附近地区硬件延迟稳定性解算结果的影响相对较小, 但在太阳活动低年, 其影响仍较为显著. 相似文献
16.
Nios Ⅱ处理器是Altera公司推出的基于SOPC系统的嵌入式软核处理器。在Quartus Ⅱ软件的SOPC Builder工具中,用户可以利用Nios Ⅱ处理器、标准配套外围设备以及用户自定义的逻辑接口IP核来创建适用的Nios Ⅱ嵌入式系统,再将设计下载到Altera公司的FPGA中进行实现。本文在Quartus Ⅱ软件中使用Verilog硬件描述语言创建了基于Avalon总线的ISA总线接口逻辑,并在SOPC Builder中实现对此元件的封装,使之成为可供Nios Ⅱ系统使用IP核。 相似文献
17.
In the face of harsh natural environment applications such as earth-orbiting and deep space satellites, underwater sea vehicles, strong electromagnetic interference and temperature stress,the circuits faults appear easily. Circuit faults will inevitably lead to serious losses of availability or impeded mission success without self-repair over the mission duration. Traditional fault-repair methods based on redundant fault-tolerant technique are straightforward to implement, yet their area, power and weight cost can be excessive. Moreover they utilize all plug-in or component level circuits to realize redundant backup, such that their applicability is limited. Hence, a novel selfrepair technology based on evolvable hardware(EHW) and reparation balance technology(RBT) is proposed. Its cost is low, and fault self-repair of various circuits and devices can be realized through dynamic configuration. Making full use of the fault signals, correcting circuit can be found through EHW technique to realize the balance and compensation of the fault output-signals. In this paper, the self-repair model was analyzed which based on EHW and RBT technique, the specific self-repair strategy was studied, the corresponding self-repair circuit fault system was designed, and the typical faults were simulated and analyzed which combined with the actual electronic devices. Simulation results demonstrated that the proposed fault self-repair strategy was feasible. Compared to traditional techniques, fault self-repair based on EHW consumes fewer hardware resources, and the scope of fault self-repair was expanded significantly. 相似文献
18.
基于CPLD的RS422接口电路设计 总被引:1,自引:0,他引:1
RS422总线目前已大量用于长距离线路通讯.阐述了一种利用CPLD作为主控单元所构成的RS422接口转换电路,该接口电路所有运算功能均采用硬件逻辑实现,具有响应速度快、可靠性高、通用性和灵活性强的特点. 相似文献
19.
评审是在研制过程决策的关键时刻.全面系统地检查设计输出是否满足设计输入的要求.发现设计中存在的薄弱环节,提出改进措施和建议.加速设计成熟,降低决策风险。航天产品的技术评审一般包括阶段评审、关键点评审和专项评审.评审分类见表2. 相似文献