模型旋翼与全尺寸旋翼风洞试验结果的比较

本文介绍了旋翼原理样机4m模型旋翼在CARDC 8m×6m闭口风洞的试验结果与全尺寸旋翼在俄罗斯TSAGI T101开口风洞试验结果的比较.     

太阳能热推进系统效率分析

太阳能热推进采用小分子量气体作为推进剂可以获取800～900 s高比冲,但提高推进系统的换热效率是目前亟待解决的问题.本研究建立了太阳能热推进系统主要部件的基本分析模型,在利用有限单元法进行热分析的基础上,对系统在多种工况下的相关参数进行了计算,分析了各部件主要参数对提高太阳能热推进系统热效率和推进效率的影响,得出了系统效率在不同工作状态下的变化规律,并提出了提高系统效率的措施.     

温度对油—气式起落架缓冲性能的影响研究

油—气式缓冲器内部的油液特性及充气压力会随环境温度而变化,进而影响起落架的缓冲性能。为了探究温度对油—气式起落架缓冲性能的影响,在起落架落震试验的基础上,提出一种缓冲器环境温度模拟方法,并分析油—气式起落架缓冲器在20~80℃环境温度下的缓冲性能。结果表明：在所研究的温度范围内,缓冲器初始充气压力对温度变化敏感,随着温...     

非均匀入口与化学非平衡效应对尾喷管性能的影响研究

基于煤油燃料超燃冲压发动机尾喷管,对均匀入口和非均匀入口、冻结流动模型和化学非平衡模型下的尾喷管内流动进行数值模拟,采用两方程RNG k-ε湍流模型对三维NS方程组进行求解,获得非均匀入口与化学非平衡效应对尾喷管性能的影响。计算结果表明,尾喷管内流动非均匀性由尾喷管非对称膨胀和燃烧室出口非均匀等因素构成,尾喷管入口流动参数非均匀分布对尾喷管推力、升力及俯仰力矩均有影响,算例中非均匀入口使得尾喷管净推力相对于均匀入口增加了1.2%左右;尾喷管性能受化学非平衡效应的影响,非平衡流动模型下的其净推力计算结果相对于冻结流动模型增加3%~4%。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

Storage life of silicone rubber sealing ring used in solid rocket motor

It is urgent to carry out detailed research on storage performance of rubber sealing ring to get the criterion for its storage life. This paper acquires material ageing regularity by theoretical analysis and experimental confirmation. On this condition, failure mode and failure criterion of typical sealing structure is studied, and the failure mechanism is found. Thus by analyzing the stress distribution, the relationship between ageing state and sealing condition is established. Rationalization proposal is put forward and storage life of sealing ring is evaluated. The research mentionedabove has special reference to the design of sealing structures and can provide reference for prolonging their service life.     

消光漆在光学系统的国内外应用

简单地列举了国内外一些消光漆的应用情况,阐述了消光漆的消光性能指标的测定方法,同时对

国内外的一些消光漆的消光性能进行了比较。

     

次流通道对双喉道气动矢量喷管的性能影响研究

为了进一步了解次流通道对双喉道气动矢量喷管(Dual Throat Nozzle,DTN)气动矢量性能的影响,基于二维DTN喷管构型进行了详细的数值模拟研究。结果表明:收扩的次流通道相对于平直的次流通道不会改善DTN喷管的推力矢量性能;随着次流流量增加,DTN的推力矢量角存在一个最大值,超过该值各推力矢量性能均会降低;次流通道宽度对DTN喷管推力矢量性能影响显著:(1)次流宽度不影响所能达到的最大推力矢量角;(2)小的次流宽度在进口总压较高的条件下具有更高的推力矢量角;(3)增大次流宽度能降低次流总压,但达到的矢量角会有所减小。     

基于某型发动机发展 STOVL 动力性能方案研究

短距起飞/垂直降落（STOVL）飞机由于其优越的作战性能,受到了世界航空大国的高度重视。通过借鉴目前最先进的 STOVL 动力 F135- PW -600发动机技术发展思路,研究了基于国内某型发动机改 STOVL 动力方案时,主发动机与升力风扇之间的匹配和约束关系。研究结果表明：随着升力风扇压比和流量的增加,主发动机升力减小,升力风扇升力增加;同一主发动机状态下,升力风扇流量越大,发动机前后升力平衡的升力风扇压比越小,总升力越大;主发动机性能越高,发动机前后升力平衡的升力风扇压比和流量越大,发动机总升力也越大。