全文获取类型
收费全文 | 8652篇 |
免费 | 947篇 |
国内免费 | 709篇 |
专业分类
航空 | 6080篇 |
航天技术 | 1046篇 |
综合类 | 662篇 |
航天 | 2520篇 |
出版年
2024年 | 76篇 |
2023年 | 228篇 |
2022年 | 296篇 |
2021年 | 276篇 |
2020年 | 257篇 |
2019年 | 252篇 |
2018年 | 158篇 |
2017年 | 203篇 |
2016年 | 233篇 |
2015年 | 252篇 |
2014年 | 396篇 |
2013年 | 377篇 |
2012年 | 536篇 |
2011年 | 557篇 |
2010年 | 387篇 |
2009年 | 443篇 |
2008年 | 443篇 |
2007年 | 427篇 |
2006年 | 387篇 |
2005年 | 407篇 |
2004年 | 421篇 |
2003年 | 463篇 |
2002年 | 411篇 |
2001年 | 345篇 |
2000年 | 273篇 |
1999年 | 202篇 |
1998年 | 201篇 |
1997年 | 155篇 |
1996年 | 148篇 |
1995年 | 153篇 |
1994年 | 182篇 |
1993年 | 133篇 |
1992年 | 149篇 |
1991年 | 143篇 |
1990年 | 106篇 |
1989年 | 138篇 |
1988年 | 34篇 |
1987年 | 39篇 |
1986年 | 9篇 |
1985年 | 7篇 |
1983年 | 1篇 |
1981年 | 2篇 |
1980年 | 2篇 |
排序方式: 共有10000条查询结果,搜索用时 15 毫秒
781.
为验证某飞机发动机承力框及接头的疲劳强度是否满足设计寿命要求,针对发动机的工作特点,编制了发动机地面试车-飞续飞载荷谱,并在飞机上进行了试验验证,从而保证了考核部位受载的真实性及试验结果的可靠性。本文对试验情况作了简要介绍,并对试验结果进行了综合分析。 相似文献
782.
QD-×××燃气轮机是由某型发动机改造成的燃气轮机,试车过程中解决了验证机起动、稳定工作并达到燃气轮机设计要求。试验数据表明:发动机改进设计后实测输出功率小于发动机设计计算功率,经过分析得出,验证机排气温度高,内涵空气流量小,是验证机输出功率小的根本原因。 相似文献
783.
郭伟 《航空标准化与质量》2007,(4):50-53
探讨了"十一五"期间"三大规范"的编制和贯彻工作,提出重点内容建议,并对"三大规范"编制和贯彻工作的创新拓展进行了探讨. 相似文献
784.
典型二元高超声速进气道设计方法研究 总被引:1,自引:2,他引:1
综合了一系列典型二元高超声速进气道的设计和性能估算方法, 给出了可行的设计原则.在满足流量、增压以及工作范围(起动性能和反压承受能力)的条件下, 给出了进气道进口、外压波系、内压缩通道、唇罩及隔离段的设计方法.采用此方法, 以H=22800 m、Ma0=6为设计点, 完成了一高超声速进气道的初步设计, 并估算得到了进气道性能参数、进气道的起动马赫数和反压承受能力, 对比CFD计算结果, 误差不大.通过该方法得到的进气道具有结构简单、流量系数大、压缩损失小的特点, 不通过优化即可得到性能较为良好的模型. 相似文献
785.
VSPWorks是应用于多DSP并行系统的嵌入式实时操作系统,其先进的程序设计思想,大大简化了传统多DSP系统的软件开发模型,既保证了软件质量,也提高了开发效率.在详细介绍了虚拟单处理器模型和系统启动过程的基础上,讨论了应用程序开发过程,并举例介绍了网络连接文件的编写方法. 相似文献
786.
余度技术是系统或设备获得高可靠性的设计方法之一。为了显著提高系统的任务可靠性,当系统发生故障时,余度系统能够自动完成系统重构,继续正常工作,从而提高了飞机的任务可靠性和安全性。本文从余度设计的概念出发,通过对余度等级、结构、数目及层次等几个方面对余度设计进行分析,结合某大屏幕显示器余度设计,给出了余度设计的基本方法,提出了一种余度管理方案,该设计思想也可用于其它机载设备中。 相似文献
787.
为适用于微型离心压气机叶轮的通流设计,对Qiu滑移因子模型加入了3个经验参数.首先对经验参数的求解方法及参数对于设计精度的影响进行了分析研究,发现其中经验参数cr对于设计精度影响较大.其次在通流设计中应用改进的Qiu滑移因子模型辅助生成叶片,用计算流体动力学(CFD)研究了cr所影响的模型滑移因子,与数值流场的出口平均滑移因子对比,得到了多种叶轮总体参数下cr的最佳取值.发现虽然微型、大型离心压气机叶轮总体参数变化范围很大,但cr的取值均以0.7左右为其最佳值. 相似文献
788.
Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization (ICAO) aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission (CO2 equivalent) per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost (DOC) are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases. 相似文献
789.
The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming. 相似文献
790.
在载人航天工程交会对接任务阶段,北京航天飞行控制中心首次实现了真正意义上的两目标协同控制,完成了协同体系构建、协同模式研究、协同技术攻关、协同方案设计、协同系统研制的完整技术演进过程.本文主要目标是对交会对接任务北京中心的两目标协同控制技术研究成果进行总结,主要涉及在交会对接任务协同控制技术体系构建、两目标关联计划工作模式、两目标注入安排协同设计与实施的经验与不足,通过对协同系统在交会对接任务中的实战应用情况,分析交会对接任务在协同自动化手段方面的成果和后续改进完善方向,为后续空间站任务设计和实现更复杂的多目标协同控制体系积累经验和教训. 相似文献