全文获取类型
收费全文 | 2112篇 |
免费 | 488篇 |
国内免费 | 390篇 |
专业分类
航空 | 1926篇 |
航天技术 | 274篇 |
综合类 | 215篇 |
航天 | 575篇 |
出版年
2024年 | 7篇 |
2023年 | 37篇 |
2022年 | 61篇 |
2021年 | 103篇 |
2020年 | 80篇 |
2019年 | 94篇 |
2018年 | 76篇 |
2017年 | 109篇 |
2016年 | 100篇 |
2015年 | 90篇 |
2014年 | 155篇 |
2013年 | 125篇 |
2012年 | 169篇 |
2011年 | 173篇 |
2010年 | 148篇 |
2009年 | 155篇 |
2008年 | 135篇 |
2007年 | 186篇 |
2006年 | 157篇 |
2005年 | 145篇 |
2004年 | 102篇 |
2003年 | 109篇 |
2002年 | 83篇 |
2001年 | 74篇 |
2000年 | 82篇 |
1999年 | 39篇 |
1998年 | 42篇 |
1997年 | 32篇 |
1996年 | 18篇 |
1995年 | 22篇 |
1994年 | 16篇 |
1993年 | 21篇 |
1992年 | 18篇 |
1991年 | 9篇 |
1990年 | 7篇 |
1989年 | 7篇 |
1988年 | 3篇 |
1987年 | 1篇 |
排序方式: 共有2990条查询结果,搜索用时 15 毫秒
261.
为了研究C/SiC复合材料紧固件的拉-拉疲劳行为,在疲劳应力比为0. 1、加载频率为10 Hz的条件下对不同应力水平的疲劳寿命进行统计。采用断口分析和金相分析方法对C/SiC复合材料螺钉疲劳破坏的细观机制进行了研究。结果表明:C/SiC复合材料螺钉拉-拉疲劳包含拉断疲劳及拉脱疲劳两种失效形式;基于双参数幂指数形式的寿命模型,两种失效形式的疲劳寿命经验公式相似;C/SiC复合材料螺钉的疲劳极限约为拉伸强度的65%~70%,若最大疲劳应力大于0. 7σmax,其材料损伤随循环次数增多而明显增大。 相似文献
262.
基于地外天体起飞的真空羽流导流技术仿真与试验研究 总被引:1,自引:0,他引:1
针对着航天器发动机羽流导流问题,基于工程经验提出了四种典型导流装置型面(包含内凹槽形式和导流锥形式等),利用计算流体动力学/直接模拟蒙特卡罗(CFD/DSMC)耦合方法,对起飞过程中羽流导流带来的气动力和气动热效应进行了数值模拟,并对不同导流装置情况下羽流场激波、航天器表面压强和热流密度分布规律进行了分析,给出了四种导流装置的导流效果评价。最后以导流锥形式开展试验,对仿真算法进行了验证。结果表明:羽流导流并没有导致发动机燃烧不稳定;综合考虑航天器羽流和发动机安全性,大导流锥导流的方案最优;在导流锥附近的激波位置及形态和仿真一致,仿真与试验的变化趋势一致,仿真算法可信,数据规律可以作为工程参考。 相似文献
263.
264.
265.
远程高超声速飞行器处于极为恶劣的气动加热与振动耦合环境中,长时间的高温与振动载荷相互叠加会导致飞行器热防护材料出现裂纹、错位、剥离或脱落,甚至会引发致命的安全事故。因此热防护材料在极端高温环境下的地面热/振联合试验测试,对于高超声速飞行器的安全可靠性设计极为重要。建立高温与振动复合试验环境,设法解决轻质多孔隔热材料在强振动下,表面温度难于准确测量与控制的难题,制作水冷式隔热装置保护价格昂贵的振动激励设备等,实现了1 500℃高温环境下高超声速飞行器轻质隔热材料的热/振联合试验。得到非金属隔热材料陶瓷纤维板内部的断裂形貌及裂纹断面特征。根据试验前、后材料的表观及微观变化以及内部结合剂的变化等试验结果,对材料进行改进。经过试验测试后,达到了使用要求。本文建立的1 500℃极端高温环境下的热/振联合试验系统及试验结果为远程高超声速飞行器热防护材料的抗振动能力评估、隔热效果确定以及材料性能的改进提供了重要支撑。 相似文献
266.
航空发动机闭环控制系统的设计过程复杂且环节繁多,如果通过某平台综合多个设计过程,必然可以简化流程,提高效率.在总结国内外相关文献的基础上,针对民用涡扇发动机,在Matlab/Simulink下,利用模块化方法构建包含稳态控制器、过渡态控制器以及极限保护器的涡扇发动机闭环控制系统仿真平台,并对其进行仿真测试和硬件在回路实验.结果表明,所构建的仿真平台满足控制系统的性能和实时性要求,具有良好的工程适用性. 相似文献
267.
基于金相显微镜观测的针刺C/C复合材料细观结构,考虑材料内部纤维的真实分布,建立了针刺C/C复合材料单胞模型。采用Linde失效准则,考虑纤维渐进损伤对材料进行了刚度折减,通过引入周期性位移边界条件,对针刺C/C复合材料的拉伸破坏进行了有限元法(FEM)数值模拟,分析了单胞模型的渐进失效过程,并预测了材料的拉伸强度。开展了针刺C/C复合材料拉伸试验,采用扫描电子显微镜(SEM)观察了材料的断口形貌,数值预测结果与试验吻合良好。针刺C/C复合材料受拉伸载荷后发生准脆性断裂,拉伸应力-应变曲线呈双线性,0°无纬碳布发生纤维断裂和基体开裂破坏,90°无纬碳布出现横向基体劈裂,最终断裂发生在针刺纤维与面内无纬碳布交叉区域。 相似文献
268.
《中国航空学报》2016,(3):824-830
Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites. 相似文献
269.
《中国航空学报》2016,(6):1695-1709
Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods. 相似文献
270.
针对采用亚格子模型进行含激波的湍流流动模拟时会面临激波附近的精度损失问题,考虑从通过亚格子模型以及数值模拟方法两方面的改进来实现湍流流动大涡模拟的精度提高.大涡模拟采用了Yee及Sj(o)green (2009)提出的高阶低耗散方法.该方法采用自适应的流场探测器以控制计算中所需区域的数值耗散,并考虑对动力学模型采用在激波位置使用Sagaut和Germano(2005)提出的单边亚格子过滤器和(或)直接禁用亚格子项等方法加以改进.对于标准的马赫数1.5和3条件下的激波-湍流干扰问题,上述新方法相较于全区域采用亚格子模型的方法均表现出了相似的精度提升.同时实现的数值精度改进方案采用了Harten的亚单元分辨过程来定位和锐化激波,并在精确激波位置附近的网格点处采用了单边测试滤波. 相似文献