石英加速度计离心机试验误差系数显著性分析

提出了一种针对石英加速度计精密离心机试验的显著性分析方法.在多位置方法分离加速度计误差系数时,由于激励不足等试验条件的限制,无法保证高次项系数的标定结果正确.离心机试验利用离心机提供的向心加速度作为仪表的输入,能够标定出高次项系数.为了确定被标定的误差系数均具有可信度,有必要对高过载试验结果进行分析,保留可信的误差系数,证明使用的误差模型无误.由于此方法的通用性,在其他试验条件下的误差分离试验中仍可运用.     

基于等 Weber 数的结冰外形修正

由于设备条件的限制,在进行结冰风洞试验时,试验 Weber 数与目标 Weber 数往往存在差异,为了获得与目标 Weber 数对应的冰形,需要对试验结果进行修正。本文分析了进行 Weber 数修正的原因,提出了根据几何特征量进行结冰外形修正的方法,并以某超临界翼型为对象,对不同 Weber 条件下的结冰外形进行了仿真,研究了Weber 数变化对结冰的影响规律,在此基础上开展了基于等 Weber 数的结冰外形修正。研究发现：(1)Weber 数主要影响冰角特征,对水滴收集特性、结冰极限及驻点冰厚度影响较小;(2)存在一个敏感 Weber 数,低于敏感值时, Weber 数变化对结冰影响不大,当 Weber 数高于敏感值时,Weber 数变化对结冰有明显影响;(3)采用本文提出的冰形修正方法,能保证冰形的宏观轮廓与目标冰形一致,修正后的冰形能适量消除由于 Weber 数误差导致的冰形差异,提高试验的精度。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

舰载直升机理论风限图飞行模拟获取方法

获取舰载直升机实用风限图,仅依靠实装飞行试验或建模仿真都是非常困难的。通过起降飞行模拟试验获取理论风限图,结合少量的海上实装飞行验证试验是一种综合较优的方法。起降飞行模拟试验需要真实飞行员和高等级飞行模拟器参与,飞行模拟器中的母舰气流场数据、母舰运动可由建模仿真或试验测试得到,且必须考虑母舰气流场的非定场特性;只有当飞行员视景或视觉反馈受限时(如能见度降低时),飞行模拟器基座的六自由度运动才是必需的;用DIPES或Bedford方法量化飞行员主观操纵负担,结合记录的客观操纵数据,评判起降难度;典型的飞行模拟试验程序包含了不同风况下的进近和甲板着舰,通常每隔15°和5kn一个风况。通过起降飞行模拟试验得到的理论风限图,可以更加有效和安全地指导海上实装飞行验证试验,最终获得实用风限图。     

某型导弹动导数风洞试验和数值模拟

动导数的精确预测对于弹箭类武器的成功研制至关重要。以某型导弹动态特性的研究为对象,在FD06风洞中采用自由振动法完成动态特性试验,获取该型导弹俯仰和滚转两个方向的典型振幅衰减曲线和动导数结果;针对该型导弹,基于双时间推进法数值求解非定常N-S方程和强迫运动方程,获取该型导弹俯仰动导数和滚转动导数。结果表明:CFD计算结果与风洞试验结果有较好的一致性;在给定马赫数和攻角下CFD数值模拟结果可以为后续工程型号研制提供参考。     

航空管路补偿器耐久性计算方法对比分析

本文研究了管路补偿器补偿位移疲劳寿命和耐久振动寿命的有限元分析计算方法。通过对某型管路补偿器有限元仿真计算结果和传统工程计算法计算的结果进行对比分析,研究管路补偿器补偿位移疲劳寿命的有限元计算方法,探索耐久振动寿命的有限元计算流程,并将结果同试验数据对比,以验证其设计方法的计算精度。结果表明,补偿位移的疲劳寿命有限元法的计算精度优于工程设计法;耐久振动寿命有限元法能够给出确定的振动应力分布情况,并预测出耐久振动寿命时间,工程设计法仅能计算出管路补偿器的自振频率,不能明确振动应力和寿命。     

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。     

尖侧缘机身布局的俯仰力矩特性及扰流板控制

针对尖侧缘机身布局在大迎角下存在的正俯仰力矩（抬头力矩）问题,通过风洞试验,首先研究了俯仰力矩的迎角分区特性及流动演化规律：线性增长区（迎角为0°~15°）,俯仰力矩线性增加,全机从附着流到形成进气道前缘涡和机翼涡;非线性增长区（迎角为17.5°~32.5°）,俯仰力矩非线性增加,机头涡出现,机头涡和进气道前缘涡逐渐增强,机翼涡增强后破裂;衰减区（迎角为35°~65°）,俯仰力矩逐渐减小,机头涡增强后破裂,进气道前缘涡破裂发展,机翼涡完全破裂。其次,发现了机身前体是产生正俯仰力矩的主要来源,机头涡是导致大迎角下正俯仰力矩的主控流动。当迎角为40°时,前体各截面正俯仰力矩在进气道前缘处达到最大,主要是由于该处机头涡诱导产生了较强的法向力。最后,提出了大迎角机身扰流板控制技术,产生了较好的控制效果。当迎角为40°时,扰流板可使正俯仰力矩减少62%,其原因是扰流板降低了机头涡涡量及其诱导产生的法向力,减少了机身前体对正俯仰力矩的贡献。该控制技术的缺点是扰流板会带来一些升力损失和附加阻力。基于尖侧缘机身参考宽度的雷诺数为2.59×10⁵。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.