2524与7150铝合金激光焊T型接头的组织与性能

介绍了2524与7150铝合金激光焊T型接头优化的工艺参数,并研究了T型接头在优化工艺下的显微组织与力学性能,进行金相分析、显微硬度测试与接头拉伸试验。结果表明:优化工艺下焊缝没有裂纹、气孔,金相组织晶粒细小、致密,焊缝区域的硬度最低;T型接头x方向的拉伸强度达到384 MPa,z方向的拉伸强度为236 MPa。     

2219 铝合金单、双道焊接头性能分析

通过对比2219 铝合金单道氩弧焊和氦弧打底+氩弧盖面双道焊接头的常温及液氮温度拉伸性
能、显微硬度分布、单向拉伸过程的数字散斑测量(DIC)结果,发现在常、低温条件下双道焊接头的拉伸强度和
延伸率均比单道焊接头高10% ~20%,单道焊接头焊缝及热影响区内材料的显微硬度值相比母材的降低程度
比双道焊接头更为显著,其主要原因是单道焊接头的一次性热输入大于双道焊,材料受热影响更严重,焊漏高
度及形状的可控性更差。     

2195铝锂合金弧焊技术研究现状

铝锂合金具有密度低、比模量高、比强度高、抗疲劳及腐蚀性能良好等特点,被认为是航空航天领域最有应用前途的结构材料之一.本文回顾了铝锂合金的发展历程,介绍了新一代2195铝锂合金的成分、组织结构及可焊接性,分析其焊接过程出现的主要问题,概述了国内外机构通过优化2195铝锂合金配用焊丝及弧焊工艺,改善接头组织结构及力学性能的...     

Effect of adding Nb foil on joint properties of laser fusion welding for TC4 titanium and 7075 aluminum alloy

It is difficult to gain effective Ti-Al fusion welding joints due to their differences in thermal properties and the appearance of brittle Ti-Al Intermetallic Compounds (IMCs). The experiments of laser fusion welding for TC4 titanium and 7075 aluminum alloy were carried out, temperature field and ductility/brittleness, as well as chemical potential of elements, were calculated, and the effect of adding Nb foil on mechanical properties of the weld was also investigated. The results suggested that Nb atoms tend to diffuse toward Al side, which is conducive to the participation of Nb in the metallurgical reaction and contributes to forming the Ti-Nb-Al IMC layer at the interface. As the thickness of Nb foil increases, the tensile-shear force of joint climbs first but then declines, and reaches the highest value of 1663 N with 0.10 mm-thickness Nb foil, representing 58.38% enhancement compared with the non-added one. Adding Nb foil slows down the heat transfer as a blocker, and thus both the melting amount of Al and the mixing area of Ti and Al decrease. In addition, Nb alloying reduces the brittleness of the Ti-Al compound. Hence, the joint properties of titanium/aluminum are improved with the addition of Nb foil.     

Through-thickness heterogeneity in creep properties of friction stir welding 7B50-T7451 aluminum alloy thick plate joint: Experiments and modeling

Through-thickness heterogeneity in creep properties of 7B50-T7451 aluminum alloy Friction Stir Welding(FSW) joints was investigated. Creep tests for three slices of the FSW joint were conducted at the temperature of 150–200 °C and applied stress of 60–225 MPa. The theta projection method was used to predict creep curves and minimum creep rate. The results show that the minimum creep rate increases and creep rupture life decreases with the increase of creep temperature and applied stress. Creep p...     

推进剂管理装置的可靠性增长及试验验证

采用原始的焊接方式焊接筛网式推进剂管理装置的收集器合格率低、可靠性差。为此,采用纯钛箔作为过渡层进行了不锈钢筛网与钛合金支压板的电阻缝焊试验以及随后这两者与钛合金骨架的电子束焊试验,然后进行了地面力学环境下的振动试验,以验证焊接方式改进后收集器的可靠性。焊接试验结果表明,纯钛箔过渡层一方面可以大幅降低筛网在电阻缝焊时的焊接热量,有效地减小筛网的热变形;另一方面可以在电阻缝焊后形成牢固、封闭的纯钛/不锈钢筛网焊缝过渡区,有效地增加电子束焊时筛网的变形抗力,从而使得焊接后试样的合格率和性能大幅提高。振动试验结果表明,焊接方式改进后收集器的可靠度置信下限从0.90增加到了0.96。     

Exploring 2D projection and 3D spatial information for aircraft 6D pose

The 6D pose estimation is important for the safe take-off and landing of the aircraft using a single RGB image. Due to the large scene and large depth, the exiting pose estimation methods have unstratified performance on the accuracy. To achieve precise 6D pose estimation of the aircraft, an end-to-end method using an RGB image is proposed. In the proposed method, the 2D and 3D information of the keypoints of the aircraft is used as the intermediate supervision, and 6D pose information of the aircraft in this intermediate information will be explored. Specifically, an off-the-shelf object detector is utilized to detect the Region of the Interest (RoI) of the aircraft to eliminate background distractions. The 2D projection and 3D spatial information of the pre-designed keypoints of the aircraft is predicted by the keypoint coordinate estimator (KpNet). The proposed method is trained in an end-to-end fashion. In addition, to deal with the lack of the related datasets, this paper builds the Aircraft 6D Pose dataset to train and test, which captures the take-off and landing process of three types of aircraft from 11 views. Compared with the latest Wide-Depth-Range method on this dataset, our proposed method improves the average 3D distance of model points metric (ADD) and 5° and 5 m metric by 86.8% and 30.1%, respectively. Furthermore, the proposed method gets 9.30 ms, 61.0% faster than YOLO6D with 23.86 ms.     

星载平面相控阵天线相位中心位姿标定方法

星载平面相控阵天线的相位中心是影响卫星成像质量的一个重要参数，针对平面相控阵天线的相位中心在卫星上的位姿标定问题，本文提出了一种标定平面相控阵天线相位中心位姿的方法。首先，建立了平面相控阵天线相位中心相对卫星主基准位姿传递的数学模型;其次，采用暗室测量系统对平面相控阵天线相位中心进行了标定，测得天线本体坐标系下的天线相位中心位置;最后，利用激光跟踪仪和经纬仪精测系统测出了天线相对卫星基准的位姿矩阵。基于本文提出的数学模型，获取了平面相控阵天线相位中心在卫星基准坐标系下的位置与姿态数据;同时，通过试验验证了平面相控阵天线紧固件的拧紧力矩，其对平面相控阵天线相位中心的影响可忽略。该方法对后续确定搭载平面相控阵天线的卫星相位中心工程验证，提供了参考。