电磁式跟踪器磁场畸变的姿态校正技术

电磁式跟踪器可以测量物体的位置和姿态,但其测量精度也容易受金属环境干扰。本文根据电磁跟踪器的工作原理,给出了电磁式跟踪器姿态校正的模型,讨论了两种不同的姿态校正实现方法:插值法和拟合法,比较了两种方法的优缺点。最后,对某一金属环境进行了畸变姿态校正的试验,给出了3个不同的姿态实际值和在此金属环境下的畸变和校正结果。试验结果表明本文提出的姿态校正算法能很好地补偿金属环境引起的电磁式跟踪器姿态的畸变。     

各级差异化多级刷式密封级间压降均衡性数值与实验研究

分析多级刷式密封级间压降分配特性理论,提出新型各级差异化多级刷式密封结构,基于流固耦合方法建立新型多级刷式密封三维实体计算模型,设计搭建新型多级刷式密封泄漏流动特性实验装置,数值与实验研究在不同工况条件下,结构参数对新型结构多级刷式密封级间压降均衡性和泄漏特性的影响规律。研究结果表明：传统结构多级刷式密封各级级间压降占比均衡性标准差为8.41,新型结构各级级间压降占比均衡性标准差最大为4.69,最小为2.07。相较传统各级相同结构,增大下游级有效流通面积的新型各级差异化多级刷式密封可有效改善级间压降的不均衡性。提高后挡板保护高度使得新型结构各级级间压降占比均衡性标准差最小,各级级间压降占比较接近,可明显改善新型结构多级刷式密封级间压降均衡性。减少刷丝束厚度和增大刷丝束与转子面间隙使新型结构多级刷式密封的泄漏量增大明显。     

Numerical studies of static aeroelastic effects on grid fin aerodynamic performances

The grid fin is an unconventional control surface used on missiles and rockets. Although aerodynamics of grid fin has been studied by many researchers, few considers the aeroelastic effects.In this paper, the static aeroelastic simulations are performed by the coupled viscous computational fluid dynamics with structural flexibility method in transonic and supersonic regimes. The developed coupling strategy including fluid–structure interpolation and volume mesh motion schemes is based on radial basis functions. Results are presented for a vertical and a horizontal grid fin mounted on a body. Horizontal fin results show that the deformed fin is swept backward and the axial force is increased. The deformations also induce the movement of center of pressure, causing the reduction and reversal in hinge moment for the transonic flow and the supersonic flow,respectively. For the vertical fin, the local effective incidences are increased due to the deformations so that the deformed normal force is greater than the original one. At high angles of attack, both the deformed and original normal forces experience a sudden reduction due to the interference of leeward separated vortices on the fin. Additionally, the increment in axial force is shown to correlate strongly with the increment in the square of normal force.     

Synergistic use of multitemporal RAMP,ICESat and GPS to construct an accurate DEM of the Larsemann Hills region,Antarctica

An enhanced digital elevation model (DEM) of the Larsemann Hills region, east Antarctica, is constructed synergistically by using highly accurate ground-based GPS measurements, satellite-derived laser altimetry (GLAS/ICESat) and Radarsat Antarctic Mapping Project (RAMPv2) DEM-based point elevation dataset. Our DEM has a vertical accuracy of about 1.5 times better than RAMPv2 DEM and seven times better than GLAS/ICESAT-based DEM. The accuracy is improved by validating the RAMPv2 DEM elevation by supplementing with GLAS/ICESat and DGPS survey data, when compared to that of DEM constructed by using GLAS/ICESat or RAMPv2 alone. With the use of accurate GPS data as ground control points reference elevations, the DEM extracted is much more accurate with least mean RMSE of 34.5 m than that constructed by using a combination of GLAS/ICESat and RAMPv2 as true reference. The newly constructed DEM 7 achieves highest accuracy with the least average elevation difference of 0.27 m calculated using 46 ground reference points. Available DEMs of Antarctic region generated by using radar altimetry and the Antarctic Digital Database indicate elevation variations in the range of 50–100 m, which necessitates the generation of local DEM and its validation by using ground truth. This is our first attempt of fusing multi-temporal, multi-sensor and multi-source elevation data to generate a DEM of any part of Antarctica, in order to address the ice elevation change to infer the ice mass balance. Our approach focuses on the strengths of each elevation data source to produce an accurate DEM.     

空间前方交会法及其在测试技术中的应用

分析了空间前方交会法的基本原理，建立了相关的理论模型，并在实验室的条件下严格测试了这种方法的测量精度；探讨了空间前方交会法在位置检测系统的测试过程中应用，详细地给出了测试的步骤以及测试数据的分析处理结果。     

超精密车床数控系统软件的研制

介绍了HCM-I型超精密车床数控系统软件的功能及工作流程．详细分析了数控系统软件的关键技术，给出了相应技术的软件流程图.     

参数分布修正的级间混合处理方法研究

本文在压气机级数值模拟的级间处理时,采用外推周向不均匀性做法,引入一个亚松弛的分布修正系数,研究了系数的取值和修正。通过对计算收敛后掺混面上通量守恒性的分析表明,该方法是一个性能优良的掺混面处理方法。此外,还研究了掺混面位置变化时流场的特征,结果发现掺混面置于动静叶轴向间距的1／4～2／3处为宜。最后,采用修改后的NAPA软件对NASA37级压气机在三种转速下的流场进行了模拟。     

Moses失速模型三维优化修正

通过低速轴流压气机失速实验,结合压气机失速仿真云图以及实验中所测得的叶片径向压力脉动图,发现失速后为部分叶高失速,而不是全叶高失速。基于失速预测Moses模型,通过比较不同径向截面计算得到的总压损失,发现沿径向叶片截面安装角的变化对模型的计算结果有影响,通过引入参数B对模型中的参数k进行改进。经过改进后的模型所预测的结果较原模型能够更加准确地预测压气机失速后的情况,改进后的模型可以为压气机设计提供良好的参考设计数据。对高亚声速轴流压气机进行改进,将高速可压这一因素考虑到模型推导中,对模型进行改进,改进后的模型相较于原模型在预测计算高亚声速轴流压气机压比特性上准确度提升了30%。      

轴向间隙对高速双涡轮转子稳定性的试验

通过轴向间隙静态试验判断轴承供气压力不同时的轴向间隙,采用时间三维谱图、轴心轨迹、频谱分析等非线性振动测试及分析方法,研究了轴向间隙对高速涡轮转子稳定性的影响.结果表明:当左右两侧轴向间隙不相等时,在升速过程中会出现气膜振荡和半速涡动现象;当左右两侧轴向间隙相等时,气膜振荡和半速涡动消失,能提高轴承转子系统的稳定性.      

一种新的激光捷联惯导系统级温度补偿方法

激光捷联惯导工作时,惯组内的温度会随着时间不断升高,引起惯性器件标度因数和零偏的变化,从而无法满足惯组在全温范围内工作.因此,有必要采取相应措施来减少温度带来的误差.提出一种通过3次样条插值法建立初始模型,不断迭代计算模型偏差修正样条曲线的方法,确立激光陀螺和石英挠性加速度计的温度误差模型存入DSP 中,最终由导航计算机实现惯组输出的实时补偿.通过标定和静态通电验证了模型的正确性和重复性,为进一步提高惯导精度奠定了基础.