0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

发动机唇口电热防冰系统性能仿真

采用三维耦合传热方法对发动机唇口电热防冰系统进行了多状态下的性能仿真,获得了唇口表面平衡温度及动态温升响应时间,以此评估防冰系统性能,并通过与冰风洞试验结果对比,对仿真过程进行了修正。研究表明:唇口表面加热区平衡温度均高于273.15 K,温升响应时间小于60 s,满足防冰需要,较为严酷的防冰状态点主要为飞行速度较大、环境温度较低的状态点;修正唇口材料导热系数后,仿真与试验结果吻合良好。研究结果能有效指导工程研制,对提高防除冰仿真分析结果的准确性提供了很好的借鉴。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

微型凸起物高超声速气动热特性研究

利用N-S数值解方法对高超声速气流中微型凸起物的气动热环境进行了计算研究,并对前斜坡峰值压力和热流跃升进行了分析,结果表明对于高雷诺数流动,由于其边界层很薄,气流对凸起物的冲击作用比低雷诺数流动大很多,给凸起物前缘和上表面带来较严重的气动热问题。研究还表明利用斜面侧扩张角可以降低凸起物后斜坡的气动热环境。最后对球锥与平板物型的差异给微型凸起物热环境特性带来的影响进行了研究,结果表明在本文计算状态下,风洞平板实验模型得到的凸起物前缘峰值压力和热流跃升比实际球锥外形要高,因此地面实验结果外推到天上实际情况还是比较保守的。     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

载人月球探测月面活动发展设想

载人月球探测是浩大的系统工程,组成复杂,关键技术多,研制周期长,经费投入高,任务风险大.月面活动是载人月球探测任务体现能力、保障安全、提升效益的重要组成部分,必须回答"为什么""去哪里""怎么干"等问题.本文从国内外月球探测历程出发,结合当今世界月球探测领域趋势与局势,从月球战略布局、月球科学内涵开展分析.针对月面驻留...     

热处理对Ti3Al/TC11双合金盘拉伸性能与组织的影响

研究了经真空电子束焊接+近等温锻造制备的Ti3Al/TC11双合金盘在不同热处理制度处理后的力学性能和显微组织.结果表明,采用梯度热处理的双合金盘的强度稍高;而塑性与变形量有关,当采用40%变形的塑性要高些.热处理制度对焊缝区显微组织有较大的影响.梯度热处理时,焊缝两侧合金的热影响区组织与焊缝中心过渡均匀、无突变,而采用一般热处理制度处理时组织则有明显的突变.热处理制度对双合金盘焊缝的相组成几乎没有什么影响,除了α1,α及β相外,还有新生成的O相,MoNb,Nb,Al及TiAl3相,它仅对组成焊缝的每一个相的含量有一定影响.     

双向扩张型孔射流角度对气膜冷却特性影响的实验

设计了气膜冷却实验台,测量了单排7个气膜孔的平均换热系数和冷却效率.气膜孔倾角为20°,45°和90°,孔间距P/d=3.动量比变化范围为1～4.重点研究主流零压力梯度下动量比和孔倾角对换热系数比和冷却效率影响.结果表明,动量比的增加使换热系数比和冷却效率都增加,随着倾角增加,动量比对冷却效率的影响减弱;倾角对换热系数比的影响非常复杂,倾角的增加使冷却效率减小.倾角20°的冷却效率明显高于倾角45°和90°的冷却效率.