涡轴发动机燃气涡轮叶片动应力测试技术研究及验证

针对涡轴发动机高转速燃气涡轮叶片动应力测试中出现的应变计短路、高温导线断裂和线芯窜动问题,开展了动应力测试技术研究。提出了加宽基底喷涂固定应变计、优化高温导线布线、改进高温导线等工艺方法,并进行了试验验证。试验结果表明,共振转速试验测试值与计算值基本一致,共振转速测试结果准确有效。通过研究,获得了具有实际应用价值的涡轴发动机燃气涡轮叶片动应力测试技术,可为同类测量提供参考。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

直升机旋翼桨叶的弹性碰撞动力学建模

建立了直升机旋翼桨叶弹性正碰撞的动力学模型,采用有限转动梁理论处理桨叶的弹性变形,利用Hertz接触理论处理局部弹性变形,引入位移协调方程识别弹性碰撞载荷,运用Hamilton原理建立了桨叶正碰撞的动力学方程.通过与Timoshenko算例的对比表明了该方法的正确性,且对集中质量与直升机桨叶的弹性正碰撞问题进行了研究.      

固体火箭发动机对交变环境温度瞬态响应的研究

在阐述了环境温度方程、传热方程和粘弹性本构关系的基础上,用有限元法求解了固体火箭发动机对交变环境温度的温度和应力响应,给出了发动机中的温度分布和应力分布,得出了发动机中危险部位和危险季节的结论。     

预拉伸条件下铝合金焊接残余应力的数值模拟

利用ANSYS有限元分析软件,通过APDL语言编程,实现了不同预拉伸应力条件下铝合金平板对接焊过程中,温度场及应力场的模拟分析.计算结果表明,预拉伸焊接法可以有效地控制焊接残余应力,随着预拉伸应力的增大,其焊后残余应力值逐渐减小.当预拉伸应力σP从0增加到90%σ0.2时,纵向残余应力降低了85.6%.模拟分析结果与实验测试结果基本吻合.     

多轴高周疲劳失效准则的对比分析

采用多种材料、多种加载方式的数据对多轴高周疲劳中比较常用的6个失效准则进行了对比分析.选取的准则涵盖目前研究的各个方面,包括等效应力准则、应力不变量准则和临界面应力准则;选用的数据包括合金钢、低碳钢、铝合金和铸铁等10种金属材料;加载方式包括比例加载和非比例加载;对比方式包括对同种材料不同准则之间的横向比较和同一准则对不同材料的纵向比较.对比分析的结果表明,6种准则对于低碳钢及合金钢材料的预测结果优于其它材料;比例加载的预测结果优于非比例加载;预测结果较满意的是Papadopoulos准则、Susmel准则和Liu准则.此外,6种准则对于铸铁的预测结果均不理想.      

MTPS蜂窝夹芯结构传热性能及热应力分析

对于金属防热结构的蜂窝夹芯结构的稳态情况,基于材料的全灰体假设,同时考虑热传导和热辐射两种传热形式对温度场的耦合作用,利用热流量守恒建立了蜂窝芯层温度场的非线性积分方程。离散化后利用数值方法得到方程组的数值解。对于美国兰利研究中心的实验结果,与本文方法的对比计算结果基本吻合。进一步,利用计算结果讨论了给定面板温度边界情况下,下面板、柱体层的灰度、蜂窝结构长径比对夹芯温度场的影响。并根据温度场和近似的应力分析模型,用半解析结果讨论了稳态情况下蜂窝芯层上的热应力。     

结冰翼型表面明冰的压力分布和应力计算

在不同来流速度和攻角下,比较分析了冰型外部压力分布的变化规律,计算分析了外部压力分布对表面冰型的力学特性影响规律,研究了冰型和蒙皮界面间最大剪切应力的变化规律,并结合剪切强度随界面温度变化的实验曲线,分析了最大剪切应力对冰层脱落的贡献.计算结果表明:最大剪切应力是剪切强度的5.48%,因此气动力对冰层的脱落贡献不大;当开启热除冰装置后,由于蒙皮表面温度的不断上升,冰型和蒙皮界面间剪切强度的下降,当表面温度为-2℃时,最大剪切应力超过剪切强度的10%,此位置可能率先产生破裂,从而加速冰层的脱落.      

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

铝合金剪切旋压残余应力分布规律

研究了剪切旋压加热温度、进给率和半锥角对残余应力分布的影响规律.试验结果表明:旋压进给比增大,残余压应力减小;适宜的旋压变形温度范围有利于降低工件表面残余应力;半锥角对工件表面残余应力的影响不显著,5A06铝合金旋压适宜采用30°～45°的半锥角.