复合材料层合板宽度尺寸效应的混合模型

研究了影响复合材料层合板强度尺寸效应的两个主要影响因素:统计尺寸效应和自由边效应。统计尺寸效应采用经典的Weibull最弱环理论描述。提出了"废宽度"的概念,将自由边效应和最终失效强度联系起来。综合这两种效应,得到了影响纤维增强复合材料(Fiber reinforced plastic,FRP)宽度尺寸效应的混合模型。引用D Kujawski的试验数据对混合模型进行了验证,结果表明:混合模型能够准确地预测不同宽度试件的最终失效强度。     

大气湍流退化图像多帧盲复原

针对图像盲复原时PSF（点扩散函数）尺寸参数对复原效果影响较大,提出一种点扩散函数尺寸自适应估计算法,该算法以均方误差为代价函数,通过遍历搜索点扩散函数有限支持域,克服了点扩散函数尺寸参数选择难的问题。仿真结果表明,估计的点扩散函数尺寸接近真实尺寸,对于大气湍流变化快的情形,改进算法取得了较好的图像复原效果。     

AP粒度对其感度、推进剂燃烧速度及临界电子激发能的影响

研究了固体推进剂中氧化剂AP的平均粒度对其撞击感度和摩擦感度的影响,以及当AP加入改性双基推进剂中后,其平均粒度对改性双基推进剂燃烧速度的影响。揭示了影响AP撞击感度、摩擦感度以及推进剂燃烧速度的主要原因,即AP颗粒大小与引起其分解所需的临界电子激发能之间的关系。这对超细AP在推进剂中的安全合理应用具有重要指导意义。     

Investigation of vertical profile of rain microstructure at Ahmedabad in Indian tropical region

The microstructure of rain has been studied with observations using a vertical looking Micro Rain Radar (MRR) at Ahmedabad (23.06°N, 72.62°E), a tropical location in the Indian region. The rain height, derived from the bright band signature of melting layer of radar reflectivity profile, is found to be variable between the heights 4600 m and 5200 m. The change in the nature of rain, classified on the basis of radar reflectivity, is also observed through the MRR. It has been found that there are three types of rain, namely, convective, mixed and stratiform rain, prevailing with different vertical rain microstructures, such as, Drop Size Distribution (DSD), mean drop size, rain rate, liquid water content and average fall speed of the drops at different heights. It is observed that the vertical DSD profile is more inhomogeneous for mixed and stratiform type rain than for convective type rain. It is also found that the large number of drops of size <0.5 mm is present in convective rain whereas in stratiform rain, drops concentration is appreciable up to 1 mm. A comparison of measurements taken by ground based Disdrometer and that from the 200 m level obtained from MRR shows good agreement for rain rate and DSD at smaller rain rate values. The results may be useful for understanding rain structures over this region.     

细粒度AP的改性双基推进剂燃速预示模型

在一维气相稳态反应流模型的基础上,讨论了细粒度AP对改性双基(CMDB)推进剂燃速的影响,引入工艺粒度d*s,修正了AP对燃烧表面结构影响因子fAP和分解影响因子gAP,建立了适用于细粒度AP的CMDB推进剂燃速预示模型,该模型可从推进剂化学结构参数出发,定量计算AP-Al-CMDB推进剂的燃速。结果表明:在压强9.8～19.6MPa条件下,不同AP粒度和含量下的燃速计算结果和实验结果吻合较好,大部分误差在5.0%,检验了模型的可靠性,对推进剂配方研制具有较好的指导意义。     

机翼用铝合金材料原始疲劳质量对比

当前航空工业的发展对于超高强铝合金材料的需求十分迫切,实现该材料的国产化并达到良好的质量效果至关重要。为了对中国航空工业中常用的7XXX新型铝合金材料的原始疲劳质量（IFQ）进行评估,选取裂纹萌生时间（TTCI）和当量初始缺陷尺寸（EIFS）作为对比参量,分别对中国飞机机翼用7XXX紧固孔试件和俄系BXXX紧固孔试件开展了低、中、高3种应力水平下的疲劳试验,通过对比分析得到了两种试件在不同应力水平下的TTCI趋于一致,最大仅相差3.71%;得到了每个试件的EIFS,应用疲劳统计学方法验证了两种试件材料各自的EIFS值无显著性差异;提出了一种不同超越概率下的结构细节当量初始缺陷模型,直接有效地对飞机结构细节的质量风险进行了评估;建立并对比分析了两种试件结构细节的通用EIFS分布,结果均小于中国军用手册规定的0.125 mm,且在超越概率为5%时,7XXX材料的通用EIFS值要小于BXXX材料的通用EIFS值。     

复杂结构模压模具的加工方法

分析了模压模具结构形状上的特点和其空间角度及尺寸加工上的难点,由于该模具结构形状复杂,加工精度要求高,其空间角度和尺寸在普通设备加工保证较为困难。重点阐明了利用现有的普通加工设备,采取相应的工艺方案来保证模具工件的空间角度及尺寸的加工方法。     

小型二冲程汽油机缸体气口尺寸的确定及其对整机性能的影响

本文以一种典型小型二冲程汽油机为例，介绍了缸体气口尺寸的确定方法，并通过发动机台架试验的结果分析气口尺寸、形状、气道质量对整机性能的重要影响。为进一步提高产品质量，提供了可靠的依据。     

Use of Optical Characteristics to Identify Orbiting Material

Knowledge of the observable properties of orbital debris is necessary to validate debris models for both the low Earth orbit (LEO) and the geosynchronous Earth orbit (GEO). Current methods determine the size and mass of orbital debris based on knowledge or assumption of the material type of the piece. Improvement in the knowledge of material is the goal of the research described herein. The process of using spectral absorption features to determine the material type is explored. A review of the optical measurements of orbital debris as well as current research in the area is discussed. Reflectances of common spacecraft materials are compared. The need for, and advances made possible by obtaining real data are explored. The prospects of the venture are investigated.     

Variation of rain drop size distribution with rain rate at a few coastal and high altitude stations in southern peninsular India

Rain drop size distribution (DSD) was measured at four places in Southern India {Thiruvananthapuram, Kochi, Munnar and Sriharikota (SHAR)} using a Joss–Waldvogel (JW) impact type disdrometer. The data for each minute were corrected for dead time errors and rain rate was computed from the corrected data. The data for a whole month were then sorted according to rain rate (R) into several classes ranging from 0.1 to >100 mm/h. The average DSD in each class was computed, and the lognormal distribution function was fitted to the average. In all the cases, the function fitted the data very well. The fit parameters were found to have dependence on rain rate. The total number of drops (N_T), the geometric mean diameter (D_g) and the standard geometric deviation (σ) were also computed from the fit parameters. The standard geometric deviation (σ) was found to be more or less constant with rain rate at all the sites and in all months. The other two parameters (N_T and D_g) were found to vary exponentially with rain rate except in Munnar, a high altitude station. At Thiruvananthapuram, in most of the months, N_T increased exponentially with rain rate up to some value of R, which was different in different months, and then remained more or less constant or decrease slightly. In all cases, the variation of N_T and D_g was such that N_TD_g³ increased linearly with rain rate.