Low C/N_0 Carrier Tracking Loop Based on Optimal Estimation Algorithm in GPS Software Receivers

Suppressing jitter noises in a phase locked loop(PLL) is of great importance in order to keep precise and continuous track of global positioning system(GPS) signals characterized by low carrier-to-noise ratio(C/N0).This article proposes and analyzes an improved Kalman-filter-based PLL to process weak carrier signals in GPS software receivers.After reviewing the optimal-bandwidth-based traditional second-order PLL,a Kalman-filter-based estimation algorithm is implemented for the new PLL by decorrelating the model error noises and the measurement noises.Finally,the efficiency of this new Kalman-filter-based PLL is verified by experimental data.Compared to the traditional second-order PLL,this new PLL is in position to make correct estimation of the carrier phase differences and Doppler shifts with less overshoots and noise disturbances and keeps an effective check on the disturbances out of jitter noises in PLL.The results show that during processing normal signals,this improved PLL reduces the standard deviation from 0.010 69 cycle to 0.007 63 cycle,and for weak signal processing,the phase jitter range and the Doppler shifts can be controlled within ±17° and ±5Hz as against ±25° and ±15 Hz by the traditional PLL.     

再入飞船通信环境建模研究

再入飞船的通信环境所受影响主要体现于飞船周围等离子体鞘对电磁波产生衰减。为了研究飞船再入过程中衰减对通信的影响,需要建立飞船外围的三维通信衰减仿真模型,在此基础上可以研究适用于再入通信环境的新型通信技术。为此文章提出了再入飞船通信衰减的动态建模方法,并根据气动、热力学和电磁波理论公式提出了具体的飞船再入动态通信环境建模方案,同时阐述了各部分建模的研究方法,为进一步研究应对黑障的新型通信技术奠定了基础。     

一种BOC调制信号的同步主峰检测新算法

BOC(Binary Offset Carrier)调制信号具有相关函数多值性,这就导致接收机同步阶段容易错锁在虚假相关主峰上。本文提出了一种新的主峰检测算法,很好地解决了接收机同步中出现的此类错锁问题。新算法通过本地增设一条QBOC支路,与BOC支路结果经补零、移位、相加计算而实现,称此算法为OQCC(Offset Quadratic Cross-Correlation)算法。理论与仿真分析结果表明,OQCC算法同时适用于奇数阶和偶数阶BOC调制信号;能够在不改变BOC信号主峰宽度的情况下,通过降低副峰,有效提高主副峰分离度;在同等条件下,可有效提高BOC信号主峰检测概率,降低BOC信号副峰检测概率。     

高分辨率多径时延测量算法

提出一种基于最小二乘准则的高分辨率多径信号时延测量方法。对参考信号作三阶样条插值获得每条多径信号最小二乘意义的最优估计,用每条多径信号的测量值重构接收信号,通过反复迭代使重构信号是接收信号最小二乘意义的最优估计,实现多径信号的时延测量。仿真结果表明：新算法在低信噪比、窄带信号条件下仍能获得较高的时延测量精度,性能优于MUSIC类时差测量算法。     

宽带信号多通道干涉仪测向解模糊方法研究

针对基于子频带分解的宽带信号干涉法测向中通道间相位差的模糊问题,提出了一种简单的解模糊方法,该方法运算量小且正确解模糊对信噪比要求低。仿真结果表明了结论的正确性。     

超光谱成像仪成像电路的设计与实现

超光谱成像仪是环境减灾-1A卫星的主载荷之一,也是我国第一台采用静态干涉型光谱成像技术的星载遥感相机。成像电路是超光谱成像仪的核心组件之一,文章介绍了超光谱成像仪成像电路的系统组成,以及各功能模块的结构、功能和设计原理。     

一种稀疏阵列下的二维DOA估计方法

研究了稀疏阵列下二维波达方向（DOA）的估计问题,提出一种基于不动点迭代的空间谱估计（FPC-MUSIC）算法。首先建立基于矩阵填充的DOA估计信号模型,并验证该信号模型满足零空间性质（NSP）,其次通过不动点迭代算法将稀疏阵列信号恢复为完整信号,最后利用恢复信号估计二维DOA。该算法可在稀疏阵列下大幅度降低谱估计平均副瓣,在大幅度降低阵元数的同时具有较高的估计精度。计算机仿真表明：FPC-MUSIC算法可在稀疏阵列下准确估计二维DOA,验证了该算法的有效性和优越性。     

宽带认知雷达低峰均比波形快速设计算法

发射波形设计是宽带认知雷达系统的关键技术。为了提高宽带认知雷达系统对距离扩展目标的检测性能,建立了目标检测模型,分析了系统的检测性能,在此基础之上研究了基于最大输出信干噪比(SINR)的低峰均比(PAR)波形设计算法。通过将原波形优化问题等效为接收权值与低峰均比波形的联合优化问题,同时利用循环优化的思想,提出了一种低峰均比波形快速设计算法。相比于现有的梯度法以及凸优化算法,该算法所设计的恒模波形信干噪比与二者相当,但算法实现难度明显变小,计算复杂度明显降低。仿真结果证实了算法的有效性。     

高保真气动伺服弹性系统降阶技术研究

采用高保真非定常气动力辨识技术获得的气动伺服弹性(ASE)系统时域模型往往阶次较高,不利于控制系统设计的应用.为了有效降低高阶ASE系统阶次,研究了高保真ASE模型的降阶特性,分别采用平衡截断、奇异摄动以及平衡奇异摄动模型降阶技术,结合BACT系统讨论了各种方法在ASE模型降阶中的应用情况,通过仿真比较得知,平衡奇异摄动法应用于ASE模型的降阶具有一定的优势,可以大幅降低模型阶次,且能够保证降阶模型的精度.     

Investigation of longitudinal aerodynamic parameters identification method for fly-by-wire passenger airliners

The flight control system of a fly-by-wire （FBW） passenger airliner with a complex frame-work and high feedback gain augmentation would change the original characteristic of a loaded signal and suppress the excitation of an airplane＇s pertinent motion modes. Taking a research example of an FBW passenger airliner model with longitudinal relaxed-static-stability, a new method of signal type selection and signal parameter design is proposed, through analysis of signal energy distribution and plane body＇s frequency response. According to CCAR60--the Appraisal and Use Regulation of Flight Simulator Device, the simulation validation of the FBW passenger airliner＇s longitudinal aerodynamic parameters identification is put forward. The validation result indicates that the designed signal could excite the longitudinal motion mode of the FBW passenger airliner adequately and the multiparameter comparison in simulation meets the objective test request of CCAR60. Meanwhile, the relative errors of aerodynamic parameters are less than 10%.