喷流噪声特性与控制研究

本文着重研究喷流噪声机理及工程计算方法。通过实验研究了声功率与喷流速度的关系,表明在Mα>0.4时Lighthill方程和Lilley方程均与实验数据吻合,可分别使用。而Mα<0.4时,均偏差较大,通过本文实验表明,若改为6次方关系较为恰当。文章同时对喷流噪声指向性、谱特性进行了分析。最后对一种引射消声器进行了发展性研究,获得在135dB噪声条件下,降噪17dB的效果。     

Using gamma-ray burst prompt emission to probe relativistic shock acceleration

It is widely accepted that the prompt transient signal in the 10 keV–10 GeV band from gamma-ray bursts (GRBs) arises from multiple shocks internal to the ultra-relativistic expansion. The detailed understanding of the dissipation and accompanying acceleration at these shocks is a currently topical subject. This paper explores the relationship between GRB prompt emission spectra and the electron (or ion) acceleration properties at the relativistic shocks that pertain to GRB models. The focus is on the array of possible high-energy power-law indices in accelerated populations, highlighting how spectra above 1 MeV can probe the field obliquity in GRB internal shocks, and the character of hydromagnetic turbulence in their environs. It is emphasized that diffusive shock acceleration theory generates no canonical spectrum at relativistic MHD discontinuities. This diversity is commensurate with the significant range of spectral indices discerned in prompt burst emission. Such system diagnostics are now being enhanced by the broad-band spectral coverage of bursts by the Fermi Gamma-Ray Space Telescope; while the Gamma-Ray Burst Monitor (GBM) provides key diagnostics on the lower energy portions of the particle population, the focus here is on constraints in the non-thermal, power-law regime of the particle distribution that are provided by the Large Area Telescope (LAT).     

数值模拟方法对NASA CRM模型阻力预测的影响

在复杂工程外形的数值模拟中，网格类型、规模和分布、湍流模型、数值格式等都会不同程度影响模拟结果。如何评估这些模拟方法对模拟结果的影响，并识别对模拟结果影响较显著的因素，对于CFD的发展方向有积极的借鉴指导意义。为了综合研究不同因素对商用运输机外形阻力预测的影响，以AIAA第六届阻力预测会议外形NASA CRM为研究对象，同时考虑了网格、湍流模型、无黏通量格式和体心梯度求解方法等因素对阻力预测的影响。分析中采用枚举法和正交试验设计两种方法，并使用了基于聚类分析的定性敏感性分析方法和基于Mckay主影响分析的定量方法，识别出对阻力预测影响较大的因素，这为数值模拟方法的发展指明了方向。     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

均匀各向同性大气湍流对声爆传播特性的影响

基于离散Fourier模态有限和生成的随机大气湍流场，采用修正波形参数方法，开展了均匀各向同性大气湍流对典型超声速客机声爆传播特性的影响分析。计算采用的超声速客机模型为自行生成的简化超声速公务机模型。首先，应用航空工业空气动力研究院自主研制的CFD软件ARI_Overset在三维空间求解Navier-Stokes方程，得到作为声爆远场传播初始值的近场空间压力分布；其次，基于Von Karman能量谱，采用离散Fourier模态有限和形式生成随机均匀各向同性大气湍流场；最后，采用修正波形参数方法模拟了声爆信号在随机速度湍流场中的传播过程。数值结果表明：各向同性大气湍流对于地面声爆特征有重要影响。与无湍流状态相比，均匀各向同性大气湍流使得地面声爆特征增强的概率约为55%，使得地面声爆特征减弱的概率约为45%，故总体而言大气湍流效应更倾向于增强地面声爆特征；均匀各向同性大气湍流对于声爆传播路径影响相对较小，但是这一变化仍会导致地面信号接收点的不确定性。     

New constitutive relation for eddy viscosity models

A new turbulent constitutive relation was directly derived from Boussinesq's hypothesis and mixing length theory, and then implemented in the standard k-ε model. The performance of this constitutive relation was validated in zero pressure gradient flat-plate boundary layer flow, fully-developed turbulent channel flow and separated flow in a plane asymmetric diffuser. The investigation demonstrated that, this new constitutive relation gave very accurate results in the former two basic cases and provided significant improvement in prediction of separated and reattachment points in the plane asymmetric diffuser. Separation and reattachment points at x/H=7.5 and 29 were calculated accurately in comparison to experimental results, and the static pressure coefficient of 0.82 was very close to large eddy simulation calculation. These results are very encouraging but further verification and extensive application of the new constitutive relation to other two-equation eddy viscosity model are needed.      

基于OpenFOAM的真实流体模型库及均相求解器开发

为了正确认识高压环境下的流体非理想性特征,及其对于低温射流喷雾过程的影响作用,将多种不同真实流体模型写入到开源CFD程序OpenFOAM仿真平台中,编译形成具有广泛通用性的真实流体热物理模型库;并将高压下真实流体特征的影响引入到压力修正算法中;开发出适用于描述超临界环境下低温流体流动过程的均相求解器。对高压下流体热物理性质的非理想性,以及超临界环境下的低温液氮射流喷注过程进行研究。结果表明:高压下的真实流体效应主要体现在低温区域,本文所建立的模型库可以在任意热力学状态范围内正确预测流体热物性;基于此模型库所开发的均相求解器可正确预测超临界环境下低温射流的详细流动特征和结构,而理想气体模型则会大幅低估射流核心区密度分布,中心线上误差高达68.9%;综合考虑计算精度和效率,PR EoS及相关模型更适合于这类超临界流动问题的求解;低温射流跨临界喷注中局部区域所发生的虚假沸腾现象会导致射流温升速率降低、体积膨胀速率加快;射流核心区压缩因子明显1,在数值仿真时必须考虑高压环境下的真实流体效应。     

预燃式等离子体射流点火器工作特性实验研究

为解决发动机点火包线小于飞行包线的实际问题,提供等离子体点火技术在航空发动机中的工程应用新思路,论文设计了一种预燃式等离子体射流点火器,实验研究了放电特性和射流特性。结果表明,预燃式等离子体射流点火器与空气等离子体射流点火器相比,在提升射流能量降低电源功率方面有着较大的优势,电流相同时通入甲烷在较大流量时可减小驱动电源功率,总流量为44L/min时,减幅可达14.99%;同时预燃式等离子体射流较空气等离子体射流稳定,且射流长度增加,扩大了点火面积,有利于点火。     

基于自适应网格的超声速液体射流破碎过程研究

为研究超声速气流中液体横向射流的破碎过程,采用脉冲背景光方法和VOF方法开展了实验和数值研究。为提高液体横向射流中气液界面和气流场特征捕捉的精确性,采用自适应网格技术对于气液界面、激波出现位置进行网格细化,计算得到了较为精细的气液界面、激波特征及涡系结构。研究结果表明:在低成本仿真模拟条件下,利用自适应网格计算得到的射流轨迹和轮廓与实验吻合较好,射流轨迹的最大误差为10%;射流初始段在超声速气流条件下,仍然存在一段高度约为1.9倍喷孔直径且圆柱形态保持较好的连续光滑液柱。随着喷注压降的升高,液柱的长度逐渐增大;主流气体流经液柱发生三维绕流,在射流附近和近壁面区域形成不断演化的反转涡对,反转涡对的形成加速了液体射流一次破碎过程。