基于格子Boltzmann方法表面形貌对微通道对流换热的影响

为推动微通道冷却技术在航空发动机中的应用,进一步提高航空发动机性能,本文通过扫描电子显微镜、粗糙度扫描仪等多方式扫描得到实际加工物体表面形貌,结合分形理论进行处理,得到真实、光滑、分形插值、康托尔集四类圆形截面管模型,管径100μm~400μm;采用格子Boltzmann方法进行数值模拟,首先通过与文献中实验结果的对比,验证了此方法的正确性,然后对空气在这四类圆形截面微通道中的对流换热特性进行了数值模拟,计算雷诺数Re范围80~640;结果发现：表面形貌是微通道中对流换热不可忽略的因素,相对粗糙度越大越有利于换热,真实扫描管的换热性能要比相同条件下光滑管高2.22%;分形理论可用于微通道表面形貌的构建,在相同迭代次数下,分形插值模型与真实扫描形貌换热性能相差0.03%,而康托尔集模型与真实扫描形貌换热性能相差1.88%,分形插值模型较康托尔集模型更能真实地反映实际形貌;微通道中,随着雷诺数的增加Nu将不再是常数,而是有增加的趋势。     

基于PaSR模型的低旋流燃烧大涡模拟

为了深入理解低旋流流场特征和燃烧稳定性,基于OpenFOAM平台,采用动态k方程模型和有限速率PaSR模型对甲烷/空气预混低旋流燃烧进行了大涡模拟,研究了气流入口速度、当量比和压力等流场参数对流场结构和燃烧非稳态特性的影响,分析了流场大尺度结构与火焰相互作用。结果表明,流场结构和火焰抬升高度受入口速度影响较小,流场和火焰形态能够保持自相似性;随着当量比和压力提高,流场扩张性增强并在燃烧区下游产生回流区,火焰稳定不依赖回流区,根部火焰锋面形状由U形转变为W形,火焰抬升高度降低。火焰锋面稳定在剪切层,剪切层产生的周期性有序涡结构引起当地流场速度脉动和火焰表面褶皱,反映了流场非稳态特性;通过剪切层监测点瞬时轴向速度分析,涡结构特征频率随速度增大而提高,由250Hz提高至300Hz,随当量比和压力提高而降低,由250Hz降低至125Hz。     

可重复使用热防护材料应用与研究进展

可重复使用热防护系统是为高速重复使用飞行器而发展的关键性技术,涵盖了地球大气环境及非地球大气环境下的弹道式再入、高马赫数巡航等应用场景。根据现有高马赫数飞行器热防护现状,对高马赫数飞行器的主要热防护系统类型、特点和使用场景进行了简要介绍。在此基础上,结合国外里程碑式可重复使用飞行器（X-15、SR-71、航天飞机、X-33、X-37B、Spaceliner等）,梳理了可重复使用热防护材料的应用与研究进展,论述了代表性可重复使用热防护材料的发展、性能、研制进度、特点及应用前景。对国外在可重复使用热防护材料研制中的设计及发展思路,以及所存在的主要问题进行了总结归纳,为可重复使用热防护材料未来的发展提供了思路。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

整体弹性结构法及在叶片流固耦合分析中的应用

针对三维叶片时域流固耦合振动响应计算普遍耗时的问题,采用一种假设整体结构的模态位移,求解固体时域响应和实现高效网格变形,发展了一种3维时域流固耦合分析的整体弹性结构方法,并应用于压气机叶片0°和180°相位角的气动稳定性分析中。结果表明,所发展方法的计算结果与传统双向时域算法和文献的结果较为吻合,而计算效率相比于传统算法显著提升;在所分析的两个相位角下,叶片振动的气动阻尼均随流量减小先增大后降低,相比于0°相位角,180°下叶片的气动稳定性大幅提高,表明该方法能有效应用于叶片的工程流固耦合研究。     

基于拓扑优化和形状优化的桨叶结构设计

直升机旋翼桨叶剖面结构设计是研究旋翼动力学设计的基础。提出一种联合拓扑优化和形状优化的 两级优化设计方法,可用于桨叶剖面结构的设计。第一级优化以变密度法(SIMP)作为拓扑优化的材料插值方 法,以桨叶体积最小化为设计目标,约束桨叶节点位移和应力,建立桨叶的拓扑优化求解模型;第二级优化以重 构的桨叶模型为基础开展形状优化,降低局部应力集中以及找到合理的边界节点位置。对优化后的模型进行 有限元分析,结果表明:通过拓扑优化和形状优化的两级优化,能够得到满足强度和稳定性要求的结构布局,为 桨叶结构设计提供指导方案。     

倍频程准则在星载电子设备结构设计中的应用

在星载电子设备的结构设计中,一般采取局部加强结构刚度来减小其响应,但对有些结构此方法效果并不理想。为减小某单机中关键部件的加速度响应,通过倍频程准则对结构进行优化设计,通过合理弱化支架刚度来降低核心部件的响应。仿真结果表明在弱化某些结构部件的情况下,使得谐振器的加速度响应降低了29%,效果明显。通过弱化非核心部件来减小核心部件的响应,有别于常规的增加整体结构刚度来减小响应,对后续电子设备的优化设计具有一定的指导意义。     

A review of topology optimization for additive manufacturing: Status and challenges

Topology optimization was developed as an advanced structural design methodology to generate innovative lightweight and high-performance configurations that are difficult to obtain with conventional ideas. Additive manufacturing is an advanced manufacturing technique building as-designed structures via layer-by-layer joining material, providing an alternative pattern for complex components. The integration of topology optimization and additive manufacturing can make the most of their advantages and potentials, and has wide application prospects in modern manufacturing. This article reviews the main content and applications of the research on the integration of topology optimization and additive manufacturing in recent years, including multi-scale or hierarchical structural optimization design and topology optimization considering additive manufacturing constraints. Meanwhile, some challenges of structural design approaches for additive manufacturing are discussed, such as the performance characterization and scale effects of additively manufactured lattice structures, the anisotropy and fatigue performance of additively manufactured material, and additively manufactured functionally graded material issues, etc. It is shown that in the research of topology optimization for additive manufacturing, the integration of material, structure, process and performance is important to pursue high-performance, multi-functional and lightweight production. This article provides a reference for further related research and aerospace applications.