全文获取类型
收费全文 | 500篇 |
免费 | 139篇 |
国内免费 | 292篇 |
专业分类
航空 | 673篇 |
航天技术 | 82篇 |
综合类 | 97篇 |
航天 | 79篇 |
出版年
2024年 | 3篇 |
2023年 | 16篇 |
2022年 | 17篇 |
2021年 | 38篇 |
2020年 | 29篇 |
2019年 | 39篇 |
2018年 | 26篇 |
2017年 | 47篇 |
2016年 | 63篇 |
2015年 | 49篇 |
2014年 | 60篇 |
2013年 | 49篇 |
2012年 | 42篇 |
2011年 | 51篇 |
2010年 | 31篇 |
2009年 | 44篇 |
2008年 | 41篇 |
2007年 | 36篇 |
2006年 | 24篇 |
2005年 | 25篇 |
2004年 | 17篇 |
2003年 | 18篇 |
2002年 | 17篇 |
2001年 | 9篇 |
2000年 | 19篇 |
1999年 | 13篇 |
1998年 | 18篇 |
1997年 | 7篇 |
1996年 | 8篇 |
1995年 | 12篇 |
1994年 | 10篇 |
1993年 | 17篇 |
1992年 | 7篇 |
1991年 | 10篇 |
1990年 | 7篇 |
1989年 | 7篇 |
1988年 | 5篇 |
排序方式: 共有931条查询结果,搜索用时 31 毫秒
161.
复合材料层合板机械连接修理拉伸性能 总被引:1,自引:0,他引:1
带损伤孔的复合材料层合板拉伸强度会降低约55%,需要对其进行修理以恢复力学性能、满足使用要求。针对带圆形损伤孔的复合材料层合板设计了机械连接修理方案,通过轴向拉伸试验评估其修理效果。根据试验条件建立了有限元模型,分析不同的修理方案对破坏模式、破坏载荷、应力分布、钉载分配等产生的影响。试验及有限元分析(FEA)均表明,修理后的复合材料层合板,其强度恢复率达到55%~60%左右,应力集中部位主要在修理区域最外侧的钉孔旁,最终破坏模式为母板沿修理区域最外侧一排钉孔断裂。使用双面修理、增加螺栓排数、采用金属补片、适当增加补片厚度,可减缓应力集中,改善钉载分配,提高结构强度恢复率。 相似文献
162.
复合材料与金属材料混合多钉连接形式是当代飞机结构中最常见的连接形式,因此对于混合多钉连接件疲劳性能的研究有助于提高对飞机结构疲劳损伤的认知。针对以Ti-6Al-4V钛合金为螺栓的ZT7H/QY9611碳纤维增强树脂基复合材料连接板与30CrMnSiNi2A金属连接板混合多钉连接结构进行数值分析和试验研究。利用有限元方法,分别对复合材料和紧固件进行疲劳损伤预测,估算复合材料连接板上螺栓孔附近的损伤,依据复合材料和紧固件的损伤量所占权重,提出了以紧固件分布和复合材料连接板铺层层数为参数的经验公式,进而有效提高混合多钉连接结构疲劳寿命的预测精度。利用试验结果将螺栓孔损伤形式进行分类讨论,探索混合多钉连接件的损伤演化方式;利用C扫描技术得到复合材料分层损伤结果,与模拟结果进行对比分析,进一步解释了模型的合理性。与试验结果对比可以看到,考虑损伤权重的寿命预测值与试验值的对数误差仅为1.1%,相对于不考虑损伤权重方法的8.4%的对数误差,该模型寿命预测精度显著提高。 相似文献
163.
针对飞机结构部件在服役过程中存在的缝隙积水导致结构材料腐蚀的问题,通过研究腐蚀产物、形貌、失重、腐蚀速率、腐蚀损伤度以及积水溶液与暴露金属的面容比、pH值等的变化,探讨了300M超高强度钢在模拟积水环境中的腐蚀行为。结果表明,300M钢在模拟积水中的腐蚀是从点蚀开始,然后点蚀坑扩展合并,逐渐发展为全面腐蚀,其腐蚀失重和腐蚀损伤度随腐蚀时间的增加而增大,腐蚀损伤度则呈现出幂函数变化趋势;随腐蚀时间的延长,模拟积水环境中的pH值从初期的4.2升到5.2再下降到4.8~5.0,平均腐蚀速率也从0.289 g/(m2·h)线性减小到0.120 g/(m2·h);电化学交流阻抗结果表明随腐蚀时间的延长,容抗弧半径逐渐增大,说明腐蚀产物对基体起到一定的保护作用,这与腐蚀速率变化规律一致;另外,不同的面容比(腐蚀介质体积与300M钢暴露面积之比)对腐蚀过程的影响是:随面容比的增加,腐蚀失重与腐蚀速率均增大。 相似文献
164.
165.
166.
167.
Artem L. Ponomarev Alamelu Sundaresan Marcelo E. Vazquez Peter Guida Angela Kim Francis A. Cucinotta 《Advances in Space Research (includes Cospar's Information Bulletin, Space Research Today)》2011
In heavy ion radiotherapy and space travel humans are exposed to energetic heavy ions (C, Si, Fe and others). This type of irradiation often produces more severe biological effects per unit dose than more common X-rays. A new Monte Carlo model generates a physical space with the complex geometry of human tissue or a cell culture based model of tissue, which is affected by the passage of ionizing radiation. For irradiation, the model relies on a physical code for the ion track structure; for tissues, cellular maps are derived from two- or three-dimensional confocal microscopy images using image segmentation algorithm, which defines cells as pixilated volumes. The model is used to study tissue-specific statistics of direct ion hits and the remote ion action on cells. As an application of the technique, we considered the spatial pattern of apoptotic cells after heavy ion irradiation. The pattern of apoptosis is modeled as a stochastic process, which is defined by the action cross section taken from available experimental data. To characterize the degree of apoptosis, an autocorrelation function that describes the spatial correlation of apoptotic cells is introduced. The values of the autocorrelation function demonstrate the effect of the directionality of the radiation track on the spatial arrangements of inactivated cells in tissue. This effect is intrinsic only to high linear-energy-transfer radiation. 相似文献
168.
Recent Developments on Damage and Fracture of Thin-Walled Complex Components Produced by Spinning
下载免费PDF全文
![点击此处可从《上海航天》网站下载免费的PDF全文](/ch/ext_images/free.gif)
The spinning technique has been widely used in the manufacture of aerospace thin-walled axisymmetric components because of its excellent formability. Damage and fracture, as the important defects that often occur and must be avoided in the forming and service stages of components, have attracted much attention of researchers. In this paper, the fracture behavior and laws of spinning components such as conical parts, tubular parts, and components with inner ribs are summarized, the typical coupled and uncoupled ductile fracture models are introduced, and their applications in spinning are analyzed. Meanwhile, the recent developments on the modified ductile fracture model in analyzing damage and fracture mechanisms of spinning are emphatically introduced. The results could provide guidance for the selection and establishment of appropriate ductile fracture models in the finite element simulation for the accurate prediction and analysis of fracture moment, location, form, damage mechanism, and evolution law, and help the development of precision spinning techniques for high-performance thin-walled complex components. 相似文献
169.
170.
无扩口管路连接件疲劳寿命预估的损伤力学-有限元法 总被引:2,自引:0,他引:2
以损伤热力学为基础,构建分式形式的损伤演化方程。针对管路连接件等轴对称形式的构件,引入等效应力和等效应变。根据损伤力学守恒积分原理,得到恒幅重复载荷下应力与寿命关系的级数表达式,根据标准件疲劳试验结果拟合得到损伤演化方程中的材质参数。利用APDL语言编程对ANSYS软件进行了开发,使得借助ANSYS软件的损伤力学-有限元数值解法成为可能。利用该方法预估了TC6钛合金标准件疲劳裂纹萌生寿命,其结果与试验数据吻合。进一步,预估了管路连接件裂纹萌生寿命,预测了裂纹扩展路径并预估了疲劳裂纹扩展寿命。本文为采用损伤力学方法来预估构件的疲劳寿命提供了一种可行的方法。 相似文献