力值加载装置控制系统设计

针对力标准机不适用于力值现场校准测试的问题,设计了一种便携式的力值加载装置。该装置采用STM32F103为主控单片机,采用高准确度AD转换器测量力值,优化了力值加载控制算法,避免了力值加载过程中可能出现的各种问题。该装置控制速度快,准确度高,适用于力值现场校准测试。     

Generalized Kutta–Joukowski theorem for multi-vortex and multi-airfoil flow with vortex production——A general model

By using a special momentum approach and with the help of interchange between singularity velocity and induced flow velocity, we derive in a physical way explicit force formulas for twodimensional inviscid flow involving multiple bound and free vortices, multiple airfoils, and vortex production. These force formulas hold individually for each airfoil thus allowing for force decomposition, and the contributions to forces from singularities(such as bound and image vortices,sources, and doublets) and bodies out of an airfoil are related to their induced velocities at the locations of singularities inside this airfoil. The force contribution due to vortex production is related to the vortex production rate and the distance between each pair of vortices in production, thus frameindependent. The formulas are validated against a number of standard problems. These force formulas, which generalize the classic Kutta–Joukowski theorem(for a single bound vortex) and the recent generalized Lagally theorem(for problems without a bound vortex and vortex production) to more general cases, can be used to identify or understand the roles of outside vortices and bodies on the forces of the actual body, optimize arrangement of outside vortices and bodies for force enhancement or reduction, and derive analytical force formulas once the flow field is given or known.     

工艺参数对砂布轮柔性抛光力影响规律的分析

为了掌握砂布轮抛光工艺参数对抛光力的影响规律,提高抛光质量,设计了四因素三水平正交试验,利用试验结果建立了抛光力预测模型,验证了模型的显著性;分析了工艺参数对抛光力耦合影响规律,结果表明：抛光力随砂布轮初始半径和粒度的减小而增大,随转速和压缩量的增大而增大;对叶片进气边的抛光实验效果表明：通过控制压缩量可以获得稳定的抛光力,进而获得理想的抛光效果。     

飞行器纵向非线性动力学建模对稳定性的影响

飞行器的稳定性分析与建立的动力学分析模型密切相关.传统的稳定性分析方法是基于小扰动假设建立线性化模型,当飞行状态中非线性特征明显时,其结果误差会带来多大的影响是人们关心的问题.通过建立飞行动力学非线性模型和气动力非线性模型,采用时间推进方法对两类非线性问题进行了比较系统的研究.数值计算结果表明,飞行动力学非线性模型与线性模型相比,周期增大、幅值减小、衰减率增大;而菲线性气动力模型对周期几乎没有影响,但对幅值有一定的影响.     

基于力约束的空心涡轮叶片陶芯定位方法

精铸蜡型作为空心涡轮叶片精铸过程重要的前期工艺转接件,其壁厚精度主要由蜡型模具型腔与内部陶芯的位置匹配关系决定。由于陶芯在模具内完全依靠定位元件实现空间定位,为减小由定位误差引起的陶芯位姿漂移,提出了一种基于力平衡约束的空心涡轮叶片精铸模具陶芯定位布局优化方法。首先,通过建立陶芯定位误差传递模型,揭示了定位误差与陶芯空间位姿扰动量之间的映射关系;其次,根据力平衡原理构建了基于力约束的陶芯定位布局优化模型;之后,针对陶芯表面定位候选点的离散分布特性,结合遗传算法给出了陶芯定位布局点的详细求解策略。最后,仿真对比证明了利用本文所提方法获得的陶芯定位方案可以在保证陶芯定位稳定性的同时提高陶芯定位精度,此外,按照优化后的定位方案压制实际蜡型,壁厚检测结果也进一步表明所提方法的有效性。     

激光击穿不同气体的激光推进实验研究

为了研究激光击穿气体工质的机理,通过测量冲量耦合系数,比较了激光在不同压强下击穿不同惰性单原子气体(氩气、氦气)的效果,试验结果表明:原子序数较大的无机气体原子可以电离出更多的电子,从而击穿阈值更低,激光能量转化为爆轰波能量的能量转化效率更高,冲量耦合系数就越大,同样条件下更容易击穿。推进剂气体不同,冲量耦合系数差别较大。测量摆角对结果的影响也较大。     

直角切口柔性铰链平行四杆机构的屈曲分析

 介绍了研究柔性铰链机构屈曲特性的重要意义。利用材料力学弯曲变形理论的挠曲线近似微分方程建立了计算直角切口柔性铰链平行四杆机构屈曲临界力的数学模型。在简单可靠的实验装置上测试了实际样件的屈曲临界力,并利用商用有限元软件ANSYS 8.0对相应的四杆机构模型进行了非线性屈曲分析。最终结果表明：理论值、实验值以及仿真值都十分接近,但仍存在一定的误差,通过原因分析,证实了存在这种误差的合理性,从而验证了所建数学模型具有较高的参考价值,可以作为柔性铰链平行四杆机构屈曲优化设计的指导理论。     

头部鼓包对不同截面机身侧力影响研究

 飞机或导弹在大迎角下飞行时会形成非对称涡,从而产生很大的侧滑力和偏航力矩。为了寻求消除侧滑力和偏航力矩或利用流动的非对称来提供飞机飞行所需的航向控制能力,研究了机头上放置小鼓包对3种不同截面的机身前体模型的影响。研究过程中采用了风洞测力和水洞流动显示的实验方法。结果表明,在20°~70°的迎角范围内,鼓包对圆锥的影响最大,对椭圆截面模型有一定的影响,对带棱截面模型的影响最小。鼓包越靠近前体头部,对侧力的影响越大。对圆锥柱体模型鼓包只能改变侧力最大值出现的迎角,而对减小最大侧力值作用不明显。对椭圆截面模型,可使最大侧力系数从1.98降到0.53,很大程度上降低了侧力。带棱截面模型对鼓包的大小和位置均不敏感。     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.