基于CCFHTLS算法的异步电动机转子故障检测

定子电流经低通滤波器处理后产生高斯有色噪声,限制了异步电机转子故障检测算法的辨识精度。针对该问题,提出一种抑制高斯有色噪声的异步电机故障检测技术。首先对采集到的定子电流进行预处理,利用逆同步旋转变换剔除基波,避免了直接检测时基波对故障辨识精度的影响。然后利用互相关函数(CCF)处理技术对高斯有色噪声的抑制作用,提出基于CCFHTLS算法的电机转子故障诊断技术。针对异步电机转子断条和偏心故障的识别进行试验,结果表明CCFHTLS算法可以有效抑制高斯有色噪声,并保留故障有用信息,显著地提高了故障检测的分辨率。     

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%;与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型;然后设计了一种能够自动调节补偿斜率的混沌控制信号;最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

改进人工蜂群算法及其轴流压气机优化应用

为了探索更优的全局优化算法并将其应用于轴流压气机气动优化上,将标准人工蜂群（ABC）算法中采蜜蜂和观察蜂探索新蜜源的方式进行改进,从而更好地利用总体蜜源的探索信息,得到改进人工蜂群（IABC）算法。经基准函数测试表明,改进算法既能提升全局寻优能力,又能加快收敛速度。采用IABC算法和经过校核的CFD数值方法搭建优化平台,对单级跨声速轴流压气机Stage35进行优化。优化变量为动叶和静叶径向6个截面的弯、掠、前缘重弯值和尾缘重弯值,以流量和压比相对变化保持在0.5%以内为约束条件,以提高绝热效率为优化目标。结果表明：在设计转速下,优化后设计点绝热效率提升0.83%,全工况范围内平均绝热效率提升2.0%,同时喘振裕度提升1.0%,验证了IABC算法在轴流压气机优化中的有效性。     

基于波长控制的光纤陀螺标度因数温度性能提高方法

光纤陀螺的标度因数与光纤环的长度、直径及光源的平均波长有关。在温度条件下,光纤环的长度、直径及光源的平均波长均会发生变化,进而导致光纤陀螺在高低温下的标度因数不同,影响温度环境下的光纤陀螺标度因数的重复性。提出了一种基于光纤陀螺波长控制的标度因数温度性能提高方法,该方法在光源驱动电路的桥式回路中增加了铂电阻组件,从而可自动调节光纤陀螺光源的管芯温度,进而控制光源平均波长的变化,以抵消光纤环有效面积因温度变化而对标度因数产生的影响,提高温度环境下光纤陀螺的标度因数重复性。试验表明,该方法将未补偿情况下光纤陀螺全温范围内的标度因数重复性(1σ)由271×10-6~280×10-6减小到了32.5×10-6~43.5×10-6,标度因数重复性误差减小了84%~88%,并验证了该方法的有效性。     

LRU可靠性评估仿真模型及实例分析

目前,有关航空维修中出现的高故障率现场可更换单元(LRU)的可靠性评估和LRU 故障组件定位等方面的研究仍鲜有报道,为此设计一种适用于LRU“更换维修暠策略的可靠性评估仿真模型,详细介绍模型中各个功能模块的设计原理和实现方法、步骤,并以某型军用飞机液压系统中常见的高故障率LRU 为例,对模型进行应用分析。结果表明:该仿真模型在LRU 可靠性评估中具有可行性和普遍适用性。     

ORB-SLAM系统优化框架分析概述

首先阐述了ORB-SLAM系统的核心思想和基本框架,介绍了SLAM系统中光束平差法的应用实现,然后针对视觉里程计部分不同的关键帧位姿优化过程分别进行了详细阐述,并利用KITTI数据集的不同序列的实验结果进行比较研究,给出了核心的光束平差法在ORB-SLAM中的具体工作方式及性能分析,最后讨论和分析了ORB-SLAM的优势和不足。