Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

PR状态方程在超临界喷射模型中的应用

针对超临界流体物性的特殊性,对超临界喷射数值模拟方法进行研究。基于PR状态方程建立了考虑超临界流体特点的超临界喷射数值模型,并采用该模型对超临界C10H22喷射到超临界N2环境中的喷射进行了数值模拟。对比研究了采用PR状态方程的真实气体模型和理想气体模型得出的密度、温度、质量分数分布以及超临界喷射长度和喷射扩张角的变化规律和差异性,并与试验数据进行了对比。结果表明:2种模型在物性预测上的差异会造成以上喷射特性模拟结果的巨大差异,理想气体模型模拟结果与试验数据误差很大,利用真实气体模型能够得到与试验数据较为吻合的结果。基于PR状态方程的超临界喷射数值模型准确可靠,可为碳氢燃料的超临界喷射现象提供参考。     

Modeling and analysis of mover gaps in tubular moving-magnet linear oscillating motors

A tubular moving-magnet linear oscillating motor (TMMLOM) has merits of high efficiency and excellent dynamic capability. To enhance the thrust performance, quasi-Halbach permanent magnet (PM) arrays are arranged on its mover in the application of a linear electro-hydrostatic actuator in more electric aircraft. The arrays are assembled by several individual segments, which lead to gaps between them inevitably. To investigate the effects of the gaps on the radial magnetic flux density and the machine thrust in this paper, an analytical model is built considering both axial and radial gaps. The model is validated by finite element simulations and experimental results. Distributions of the magnetic flux are described in condition of different sizes of radial and axial gaps. Besides, the output force is also discussed in normal and end windings. Finally, the model has demonstrated that both kinds of gaps have a negative effect on the thrust, and the linear motor is more sensitive to radial ones.     

水下超声速过膨胀燃气射流的流场特性

为研究水下超声速过膨胀燃气射流的流场特性,在压力水筒中开展了大扩张比锥形喷管的固体火箭发动机水下点火实验,并基于雷诺时均Navier-Stokes（RANS）方法和流体体积（VOF）模型进行数值求解,分析了过膨胀燃气射流与水介质的相互作用过程。研究表明：超声速过膨胀燃气建立射流通道后,射流核心区长度随喷管落压比的减少而减少;射流核心区剧烈振荡,表现为高频的膨胀和收缩,振荡频率随喷管落压比的减小而增加,范围为100~200 Hz;射流边界不断振荡,并伴随波系结构变化,当过膨胀程度较大时,激波进入喷管使其发生流动分离现象,流动分离点周期性往复移动;分离区内压力脉动没有显著的特征频率,主要集中在100~600 Hz的宽频带,锥形喷管水下流动分离的简易判据为喷管出口压力不低于环境背压的0.44倍。     

延伸冲击孔冲击冷却流动与换热特性的数值研究

采用数值模拟方法研究了延伸冲击孔冲击冷却系统的冷却特性,分析了3个冲击雷诺数和5个冲击孔延伸长度对冲击腔内流动与换热特性的影响,给出了靶面努塞尔数分布、靶面压力分布、中心截面流速与综合换热性能的变化。结果表明：延伸冲击孔可以有效地防止横流对冲击射流的偏转作用,同时使射流出口更加贴近冲击靶面壁面,冲击速度更高,可以明显提高靶面的换热系数,并使整个靶面上的换热系数分布也更加均匀。冲击冷却的冷却性能随着冲击孔延伸长度的增加而增加,相较于传统冲击冷却（baseline）,在L/d=2.5时靶面平均努塞尔数提升达15%以上,但压力损失也相对较高;对比不同延伸长度冲击孔的综合换热性能,发现存在最佳的L/d取值范围使冲击冷却系统获得最佳的综合冷却性能。在本研究范围内,最佳的L/d= 2.5。     

空腔流激振荡的简化模型分析及振荡频率预估

本文由矩形空腔后缘声振动反馈激励腔口自由剪切层不稳定波的观点出发,把空腔流动振荡问题构造成一个关于空腔内外扰动波的非齐次边值问题,应用Ｆｏｕｒｉｅｒ－Ｌａｐｌａｃｅ变换技术求解,可以预估振荡频率,对Ｌ／Ａ＝Ａ亚声速空腔流动的预估结果与实验符合很好,揭示了此类空腔流动振荡的机理。     

模拟高度复杂流动的自适应网格算法

提出一种基于对等弧分布律进行扭转修正的自适应网格算法。该方法将三维网格系统分裂为３个单方向自适应网格子系统,在计算中与主控方程的求解格式相耦合,交替地使用。应用所构造的算法结合ＭａｃＣｏｒｍａｃｋ显式格式对喷流／绕流干扰流场进行了雷诺平均Ｎ－Ｓ方程模拟,给出了清晰的剪切层与激波波系结构。计算结果表明,该自适应网格算法可较大程度地提高ＭａｃＣｏｒｍａｃｋ格式的分辨率。     

合成射流控制NACA0015翼型大攻角流动分离

为了研究合成射流激励器处于NACA0015翼型回流区时对其分离流动的控制,采用商用计算流体力学软件Fluent 6.1求解Reynolds平均Navier-Stokes方程,通过对翼型气动力特性、脱落漩涡结构以及射流孔口附近流动结构的分析,揭示了合成射流处于分离区时对边界层控制的机理.结果表明:当合成射流孔口处于回流区时仍可有效推迟翼面边界层分离点,缩小回流区范围,从而有效提高翼型的升力.当射流方向垂直于壁面,无量纲频率以及吹气速度比都等于1时,翼型平均升力系数提高40%左右.      

Periodic atomization characteristics of an impinging jet injector element modulated by Klystron effect

An experimental study on the Klystron effect of periodic injection modulated by pressure drop fluctuations on subsequent atomization is conducted. Time-resolved atomization backlit images and atomization Mie scatter images are captured by using the high speed camera. It is found that periodicity of forced atomization relies on pressure drop fluctuation amplitude and phase differences between atomization and pressure drop fluctuations relate to fluctuation frequencies. This feature of periodic atomization induced by Klystron effect corresponds to periodicities and high amplitudes of pressure fluctuations in unstable combustion chambers and chaos and low amplitudes of pressure fluctuations in stable combustions chambers. Drastically periodic varying of gross surface area of droplets with time was shown in Mie scatter images. The importance of periodic impinging jet atomization modulated by pressure drop fluctuations for acoustic liquid propellant combustion instabilities is illustrated.     

缩比发动机喷嘴热喷流噪声试验

为深入了解涡扇发动机喷流噪声特性,验证喷流噪声降噪方法,建立发动机喷流噪声数据库,在法国国家航天航空研究中心的CEPRA19声学风洞开展了缩比发动机喷嘴热喷流噪声试验测试工作。针对发动机热喷流模拟系统,设计加工了面积比（外涵喷嘴面积与内涵喷嘴面积之比）为5和7的两种喷嘴构型试验模型。通过减小高温区域单个零件长度尺寸和零件壁厚的方法,降低热膨胀对模型尺寸的影响。在声学风洞中完成了不同工况条件下两种面积比圆形喷嘴和锯齿形喷嘴的远场噪声特性测试。通过对远场测量噪声频谱进行分析,发现随着来流速度的增大喷流噪声会减小,采用锯齿形喷嘴设计在中低频喷流噪声水平降低,在高频噪声水平有所增加。