防烟供氧面罩漏气系数试验系统的设计及应用

介绍了防烟供氧面罩漏气系数试验系统的设计与试验原理。该系统采用单元分体式结构，将气路、油路、机械各部分集成于一体，在软件作用下，通过电气电路，控制油雾的产生，保证油雾发生的流量，控制油雾室浓度的高低，控制取样流量的大小，并通过油雾浊度仪读取检测数据，完成试验过程的自动控制。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

某型APU主机滑油消耗量大故障排除

针对某型辅助动力装置修理后试车中多次出现主机滑油消耗量大的故障,分析了辅助动力装置滑油系统工作原理,查找故障原因,并制订了相应的控制措施,解决了因主机修理原因造成的辅助动力装置滑油消耗量大故障。     

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

超声速变马赫数风洞流场参数线性变化验证

旋转喷管型面使超声速变马赫数风洞在单次运行过程中可连续调节实验区的马赫数,便于研究飞行器的机动过程、进气道起动过程中的气动问题。在控制喷管型面旋转过程中,流场参数能否线性变化是衡量超声速变马赫数风洞性能的一个重要指标。分析变马赫数风洞实验区流场参数的线性变化规律,利用弹簧光顺的动网格技术建立数值仿真模型,验证喷管位于马赫数3.041~3.215 范围所对应的位置时,实验区流场参数是否满足线性变化规律。结果表明：通过对喷管型面旋转的控制实现了风洞实验区流场参数的线性变化,动态计算结果与预期实验区流场参数线性变化规律吻合良好;在不同加速度的流场参数线性变化过程中,各时刻实验区的平均参数与预期参数之间的偏差均小于0.13%。     

基于模型的转子系统不平衡量的估计

采用基于模型的方法对转子系统的不平衡量进行估计,首先记录初始状态下的振动信号,然后根据实时测得的不平衡响应信号,得出差值振动信号,联立转子系统的动力学方程,得出不平衡等效载荷,根据等效载荷,得出不平衡的位置、相位及大小.采用模态扩展技术实现由有限几个点的振动响应获取所需点上的响应.由于噪声的影响,提出了基于高斯小波的降噪方法.仿真与实验结果表明,这一方法能够比较准确地估计出转子系统的不平衡量.      

2.4米跨声速风洞大展弦比飞机测力试验技术研究

针对大展弦比飞机的气动布局特点,在2.4米跨声速风洞中开展了大展弦比飞机测力试验技术研究。该项研究建立了大升阻比高精度天平设计技术和模型支撑系统设计平台,研制了专用大升阻比高精度测力天平和模型支撑系统。在国内高速风洞中建立了大型跨声速风洞模型设计新准则。研究结果表明:所提出和制定的方案是科学合理的,为我国大飞机研制提供了可靠的技术支撑。     

连续离子层吸附反应法制备超薄功能膜及应用

阐述了液相法中制备超薄功能膜的新方法——连续离子层吸附反应法(Successive Ionic Layer Adsorption and Reaction,SILAR)。探究了它的薄膜生长机理、工艺参数影响以及应用现状,指出了尚需深入研究的问题。