BT-14钛合金舱口外盖白斑问题

BT-14钛板为某产品舱口盖结构用材料,焊前检查时,发现钛板表面有数量不等的白色圆状斑点。文章从白斑的外观形貌、微观组织以及力学性能等方面进行分析,重点研究了白斑组织对钛板使用性能的影响,并提出后续生产中的预防措施。     

Improving tensile-shear properties of friction stir lap welded dissimilar Al/Mg joints by eliminating hook defect and controlling interfacial reaction

To improve tensile-shear properties of fiction stir lap welded(FSLW) dissimilar Al/Mg joints, pin-tip profiles were innovatively designed and welding speed was optimized, and effects of them on formation, interface microstructure and mechanical properties of different FSLW joints were investigated. With increasing the welding speed, the tensile-shear load of FSLW joints produced by three pins presents an increasing firstly and then decreasing trend. Compared with Rpin, the hook and hole defect i...     

起圈织物泡沫夹芯复合材料Ⅰ/Ⅱ型断裂韧性研究

夹芯复合材料在受到弯曲、剪切和冲击等载荷作用下易发生脱层损伤。脱层损伤程度与Ⅰ、Ⅱ型断裂韧性密切相关。起圈织物由于在其厚度方向引入环状纤维束，增强了与芯层的结合能力，使其在抗分层方面性能优良。本文主要研究起圈织物泡沫夹芯复合材料的Ⅰ/Ⅱ型界面断裂韧性。根据试验标准分别制作了平纹织物泡沫夹芯复合材料和起圈织物泡沫夹芯复合材料。采用双悬臂梁试验（Double cantilever beam, DCB）和末端缺口挠曲试验（End notch flexure, ENF）对上述试验件的增韧机理进行了研究。研究表明，环状纤维束的引入大大提高了界面性能。起圈结构相较于平纹结构的Ⅰ型断裂韧性GⅠC提高了434%，Ⅱ型断裂韧性GⅡC提高了400%。通过建立有限元模型，采用内聚力模型来描述裂纹的扩展，数值结果与试验结果吻合较好。     

Effect of Isothermal Forging on the Microstructure and Mechanical Properties of Mg-8Gd-3Y-0.5Zr Alloy

Aiming at the problems of poor plastic forming ability， narrow forging temperature range， and strain rate sensitivity of rare earth magnesium alloys， a study on the microstructure and mechanical properties of Mg-8Gd-3Y-0.5Zr alloy with different isothermal forging processes is carried out. The microstructure and properties of the alloy in the as-cast， isothermal forged， and post-aging states after forging are studied with optical microscope (OM)， scanning electron microscope (SEM)， and tensile testing. The results show that significant dynamic recrystallization occurs during the isothermal forging process， a fine equiaxed grain structure is formed， and the mechanical properties of the alloy are greatly improved. When the isothermal forging temperature is 460 ºC and the strain rate is 0.02 s－1， the alloy structure performance is the best， the room temperature tensile yield strength (TYS) is 218 MPa， the ultimate tensile strength (UTS) is 299 MPa， and the fracture elongation (FE) is 19.2%. When the alloy is post-forging artificial aged， the α-Mg matrix is dispersed， the Mg5(Gd，Y) phase is precipitated， the UTS of the alloy is increased to 392 MPa， and the FE is reduced to 12.0%.     

激光熔化沉积15-5PH沉淀硬化不锈钢组织及拉伸性能

利用激光熔化沉积技术制备15-5PH沉淀硬化不锈钢板,利用金相显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)技术,对沉积态组织进行分析,测试沉积态组织的室温拉伸性能。结果表明:激光熔化沉积15-5PH不锈钢沉积态组织由沿沉积增高方向贯穿多层外延生长的柱状晶组成,柱状晶内包含多个细长整齐排列的胞状树枝晶,枝晶内为马氏体组织,枝晶间为铁素体;沉积态组织中弥散分布大量细小的NbC析出相,尺寸12～20 nm;15-5PH不锈钢沉积态组织具有良好的力学性能,纵向抗拉强度和延伸率分别为1 128.5 MPa和14.0%,横向抗拉强度和延伸率分别为1 101 MPa和12.25%。     

Microstructure and Hot Deformation Behavior of Mg-9Al-3Si-0.375Sr-0.78Y Alloy

Using Gleeble-3500 thermal simulator， the high temperature plastic deformation behavior and microstructure evolution of Mg-9Al-3Si-0.375Sr-0.78Y alloy are investigated at the temperature of 523 K?673 K and the strain rate of 10-3 s-1?10 s-1. True strain-true stress curves show the characteristics of the typical dynamically recrystallization process. The Arrhenius constitutive equation of the hyperbolic model is established. The average activation energy and the strain rate sensitivity index are， respectively， 221.578 kJ.mol-1 and 0.137. The result shows that the α-Mg phase exhibits dynamic recrystallization (DRX) characteristics obviously. But no DRX occurs in theβ-Mg17Al12 phase. Hot deformation does not affect the primary Mg2Si phase. Under the conditions of low temperature (523 K?673 K) and high strain rate (1 s-1?10 s-1)， the flow instability and macro-defects such as crack appear in the specimens. However， there are finer recrystallization grains. Under the conditions of high temperature (≥673 K) or low strain rate， the microstructure of the alloy shows good homogeneity. The size of the primary Mg2Si phase is uniform， the size of the β-Mg17Al12 phase is small， and the distribution of the β-Mg17Al12 phase is uniform.