MD-130 胶黏剂固化工艺及空间适用性研究

为满足航天电子产品的工艺实施和空间服役要求,本文详细开展了MD-130胶黏剂的固化工艺及空间适应性研究。结果表明,在150℃等温固化60 min后其拉伸剪切强度达到18 MPa,表明其为优选的固化工艺。高低温环境冲击和低剂量的粒子辐照后胶黏剂固化反应更加充分,其芯片剪切强度提高,而大剂量辐照致使高分子降解现象明显,造成了胶接强度的降低。经环境试验后,MD-130胶黏剂仍具有良好的力学性能,满足设计使用要求。     

WC/C复合涂层海水环境的耐蚀性与摩擦性能

采用非平衡磁控溅射技术在304L不锈钢和单晶硅基底上沉积WC/C多层复合涂层,利用扫描电镜、Raman光谱仪、X射线衍射仪等研究WC/C复合涂层的微观结构,采用纳米压痕仪、划痕测试系统测试涂层的力学性能,利用电化学测试系统和摩擦磨损试验机分别研究涂层在人工配置的海水环境的耐蚀性能和摩擦性能。结果表明:WC/C复合涂层内含有较多类石墨sp2键结构,存在WC1-x相并镶嵌在非晶碳基质中。较之于304L不锈钢基底,WC/C复合涂层在海水环境中表现出更好的耐蚀性与更优异的摩擦适应性。     

陶瓷隔热瓦的缺陷修补

分别采用了MgO、YSZ和Al₂O₃三种陶瓷粉体和一种含隔热瓦本体成分的粉料对陶瓷隔热瓦缺陷进行修补。研究了修补前后材料的微观形貌、力学及隔热性能。结果表明：采用含隔热瓦本体组成的粉料对陶瓷隔热瓦进行修补,修补部位与本体部位相容性好,且微观形貌相似,仍保持纤维搭接的多孔空间网络结构;修补后试样密度0.24 g/cm³、室温热导率0.044 W/（m·K）、压缩强度0.58 MPa;1 200℃、30 min热处理后,修补部位与本体部位结合性好,未出现裂纹、凹陷等缺陷,是有效的缺陷修补方法。     

金属-氟塑料自润滑材料的摩擦磨损特性

对奥贝球铁衬套材料和金属氟塑料自润滑衬套材料的摩擦磨损性能进行研究.结果表明,金属氟塑料自润滑材料与45钢配副的摩擦系数远远低于奥贝球铁材料与45钢配副,金属氟塑料自润滑材料的耐磨性能也优于奥贝球铁材料.由于金属氟塑料自润滑材料优良的自润滑性能,与其配对的45钢的磨耗量也远远低于与ADI对磨的45钢.     

惰性块式平面波发生器形成平面波的数值模拟分析

探讨了惰性块式平面波发生器的相关原理,在费马原理的基础上设计了平面波发生器的物理模型,用非线性有限元方法对平面波形成过程进行了数值模拟,得到了不同时刻的波形图像,数值模拟结果与实际过程在物理宏观特征上基本一致。     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

保载条件下FGH95材料的疲劳特性及寿命建模

针对FGH95粉末冶金材料进行了650℃时不同保载形式(拉伸保载、压缩保载和拉压保载)的疲劳试验, 分析了其变形特征和疲劳寿命分布特征以及保载对疲劳寿命的影响.并据此, 为改进保载条件下疲劳寿命的建模, 提出了迟滞环位置-形状修正因子的概念, 进而得到了一种修正的非弹性应变能~寿命方程.经对该材料疲劳试验寿命的建模和计算分析表明:该方法相比其他几种工程上经常采用的寿命预测方程, 较好地解决粉末冶金材料高温保载疲劳时的寿命建模问题, 且该方程对试验寿命预测的精度更高, 形式简单, 具有明显的物理意义.      

陶瓷纤维梯度增强活塞的梯度方程研究

 功能梯度材料零件具有单质材料零件无法比拟的理化性能优势,然而由于材料分布复杂以及对功能梯度材料本身性能研究不充分,使性能分析存在很多困难。论文应用复合材料热性能理论,采用有限元分析软件ADINA,分析陶瓷纤维梯度增强活塞（材料梯度方程的参数不同）的温度分布和应力分布,结果表明陶瓷纤维梯度层可以明显改变活塞温度分布,缓和由于热膨胀系数不匹配,在陶瓷纤维增强层与活塞本体交界处产生的应力。根据计算结果拟合出温度峰值、整体应力峰值和层间应力峰值与方程系数之间的曲线,并加以验证。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.