某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

冷气模拟推力室研究

为了模拟小推力液体火箭发动机的主要性能参数,对冷气模拟推力室进行了研究。通过理论计算、试验研究等方法,给出了合适的设计参数,使冷气模拟推力室的工作过程及主要性能参数完全可以模拟真实推力室。     

涡轮性能实验研究

对液体火箭发动机主涡轮的性能试验进行了介绍。主要包括涡轮性能吹风试验系统的配置、模拟试验参数的选择、性能换算方法的确定和试验数据的处理方法。同时对热试车后涡轮性能的计算也作了介绍,并将热试结果与模拟试验结果进行了对比,肯定了模拟试验的正确性。最后就实际应用中的一些问题进行了分析。     

Experimental Study on Emission Performance of an LPP/TVC

A key issue in the commercial aircraft engine design is environmental acceptability, and designers are continually challenged to reduce emissions. In this paper, an experimental investigation is performed to evaluate the emission performance of a liquid-fueled trapped vortex combustor (TVC) under lean premixed prevaporized (LPP) mode. When operating as an LPP system, a TVC is fueled both in the cavities and in the main stream. The correlations between the emission performance and the total excess air ratio, the positions (4 positions) of the fuel injectors in the main stream, and the inlet temperature are obtained. Experi- mental results show that both the volume concentrations of unburnt hydrocarbon (UHC) and NOx (NO, NO2 usually grouped together as NOx) increase with the increase of total excess air ratio from 1.5 to 3.0; the emission performance relies heavily on the position of the main stream injector, and the best performance is achieved at Position 4 in the experiments; the increase of the inlet temperature impacts on the emission performance positively; the smallest volume concentrations of UHC and NOx obtained in the experiment are 94×10 6 and 2.3×10 6 respectively. This paper validates the feasibility of low emissions for an LPP/TVC and provides a reference for further optimization of TVCs.     

液浮惯性仪表温度场的仿真分析

液浮惯性仪表精度跟温度场有关联,温度分布不均匀和温度波动都会对仪表精度产生影响,因此研究液浮惯性仪表内部的温度场分布尤为重要。利用有限元方法对液浮惯性仪表进行温度场仿真计算,根据仪表的结构特点合理的设置了测温点,通过试验的方法提取了特征点的温度值,验证了仿真结果的正确性,为液浮惯性仪表的热设计提供了基础参数。     

煤油液滴高压蒸发特性

采用真实流体模型描述高压下流体热物理性质的非理想性,并采用状态方程（EoS）法计算多组分高压气-液相平衡及环境气体溶解性,在此基础上建立包含亚临界和超临界两种不同机制的瞬态液滴高压蒸发模型。针对中国新一代高压补燃液氧/煤油发动机,详细研究了煤油液滴在超临界环境下的高压蒸发特性及各因素影响机理。结果表明：高压环境会显著加快液滴温升速率,但弱超临界环境下仍然为相平衡控制的亚临界蒸发状态;只有强超临界环境下才较容易发生扩散控制的超临界蒸发状态。在高压、高温环境下,忽略气相溶解性将导致液滴蒸发速率明显偏小。针对弱超临界环境,温度升高会使液滴蒸发速率单调增加;压力升高则在低温下降低蒸发速率,而在高温下加快蒸发速率。针对强超临界环境,温度升高只提升初始亚临界蒸发阶段的蒸发速率,而超临界蒸发阶段的蒸发速率与环境温度无关;压力升高则同样会提升初始亚临界蒸发阶段的蒸发速率,但会降低超临界蒸发阶段的蒸发速率,此时的总蒸发寿命随压力升高小幅下降。     

液体推进燃料着火特性影响因子与活化能分析

采用反射激波管实验台,对液体推进燃料RP-3着火特性进行了实验研究,并分析了燃料的表观活化能。采用了最大OH-光谱斜率倒推法确定着火终点,判定得到了液体推进燃料的着火特性,并对不同燃料体积分数下的着火延迟进行了归一化处理。结果表明:推进燃料的表观活化能差异不大,约为154～171kJ/mol;对各参数影响因子进行分析,着火延迟时间与当量比成正比关系,与燃料体积分数和混合气压力成反比关系;与JP-10比较发现,着火特性数据受燃料体积分数、当量比的影响因子几乎相等。      

液体推进剂热稳定性研究方法探讨

为研究液体推进剂的热分解特性,利用差示扫描量热仪（DSC）和绝热加速量热仪（ARC）,对自行研制的3种液体推进剂进行了热分解过程研究,并对其热稳定性进行了探讨.分析了DSC和ARC两种方法在研究液体推进剂热分解方面的优劣性.     

Self-perspiration garment for extravehicular activity improves skin cooling effects without raising humidity

Introduction

The current U.S. extravehicular activity (EVA) suit in space includes liquid cooling and ventilation garment (LCVG) to control thermal condition. Tubes knitted in LCVG for flowing water interrupt evaporation of perspiration, and astronauts feel discomfort. In the present study, we hypothesized that a self-perspiration garment would effectively lower the skin temperature without raising humidity in the garment. Thus, we developed and examined the effects of the garment.

Methods

Eight healthy subjects were studied with a cyclic ergometer of 30, 60 90 and 120 W loading for 3 min each. Skin temperature and humidity on the back were measured continuously. Subjects wore and tested three types of garments i.e., a spandex wear without any cooling device (Normal), a simulated LCVG (s-LCVG) or the spandex wear knitted a vinyl tube for flowing water, and the spandex wear with a tube, which flows water and self-perspiration with oozing water for evaporative cooling (SPEC).

Results

All measurements were reached to steady state 2–3 min after the setting. The s-LCVG decreased skin temperature 0.39±0.14 °C during 12 min of cooling. With SPEC, skin temperature did not decrease significantly until 6–9 min after starting the cooling. However, the temperature decreased rapidly and significantly after that, and finally decreased 1.59±0.32 °C. Humidity in the SPEC was significantly lower than that in s-LCVG.

Discussion

SPEC was effective for lowering skin temperature without raising humidity in the garment. The concept is expected to use as a better cooling system during EVA.     

液态水相变发散冷却的实验

以液态水为冷却介质,采用高温合金粉末烧结多孔材料制造平板实验件,实验研究了具有液态水相变的发散冷却特性.用远红外热像系统记录实验平板热端表面温度分布,通过热电偶及压力传感器监控冷却腔内温度和压力变化,从而分析液态水的相变过程.实验表明:随着液态水注入率的增大,平均冷却效率不断提高;当液态水在暴露于高温主流的平板表面发生气液相变时,平均冷却效率趋于稳定且不再大幅上升;主流温度与液态水注入率决定了液态水的相变位置,并对冷却腔内压力变化产生影响.