电沉积CeO2/Zn纳米复合涂层

将纳米氧化铈颗粒加入镀锌液中进行复电沉积制得纳米复合涂层。通过失重法，ICP，SEM和XRD方法探讨了纳米氧化铈颗粒对电沉积锌涂层的影响。结果表明，在同样的电沉积条件下，纳米复合涂层的耐蚀性明显提高，而微米复合涂层的耐蚀性只稍有改善；纳米复合涂层中氧化铈的含量高于微米复合涂层中的氧化铈含量。纳米氧化铈颗粒改变了锌涂层的表面组织形貌和晶体结构，从而提高了涂层的耐蚀性。     

空天飞机的边界层转捩

本文概述了边界层转捩对空天飞机性能的影响。在介绍确定边界层转捩起始点的线性稳定性理论和简单关联公式之后，又从噪声影响、头部钝头影响和钝锥飞行试验结果等几方面，讨论了线性稳定性理论的应用。接着介绍了采用转捩函数来确定转捩区的方法。从飞行试验、理论计算和风洞试验等三方面，探讨了进一步研究高超声速边界层转捩的途径。重点介绍了ＮＡＳＡＬａｎｇｌｅｙ研究中心的超声速、高超声速静风洞技术的发展。最后，对今后空天飞机边界层转捩的研究工作提出了建议。     

超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

后向台阶层流分离剪切层特性研究

应用激光测速仪对生向台阶层流边界层分离产生的剪切层在再附前的发展进行了测量，得到了时均速度、湍流强度及剪切层厚度等的分布特性，并研究了来流湍流度对台阶后流场湍强度分布及剪切层发展的影响，实验中发现台阶后有一个流速降低的区域，对此从涡动力学的角度作了解释。     

复合材料层合残余应力实验研究

取单向板90°试样用DMA法测出的玻璃化温度T_(?)为应力释放温度,用应变片包埋法测定了玻纤/648环氧复合材料单向试样与对称正交层板的热应变,用经典层板理论处理实验结果,实验值与理论值吻合;结果还表明,一般意义上的复合材料内的层合残余应力与制造过程中复合材料内的残余应力应作区别。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。     

Effect of curing condition on bonding quality of scarf-repaired composite laminates

Both single-face vacuum bag curing (SVC) and double-face vacuum bag curing (DVC) can be used in scarf repair of composite structures. But different curing conditions caused by the sealing state may affect the bonding quality of scarf-repaired structures. In this paper, the effect of curing condition on bonding quality of scarf-repaired laminates was experimentally investigated in terms of surface profiles, moisture absorption curves and section profiles. In order to further explore the moisture absorption mechanism, finite element model of the repaired laminates using DVC was established with moisture diffusion of both the adhesive and composite laminates considered. This model was verified by experimental results. Based on the model of DVC case, the model of SVC case was built by changing moisture absorption parameters of the adhesive. Results show that SVC reduces the bonding quality, mainly reflecting in more adhesive inner voids and patch-to-parent dislocation. And SVC increases moisture absorption rate and moisture equilibrium content of the adhesive, and its effect on the former is far greater than that on the latter.     

Diurnal and seasonal variations in long-term changes in the E-layer critical frequency

Long-term changes in the E-layer critical frequency, foE, at three stations of the European region (Juliusruh, Slough and Rome) and also at Moscow and Wakkanai stations are analyzed by the method developed by the authors and described in detail in the previous papers. It is found that Juliusruh and Slough stations demonstrate a well-pronounced change in foE (a trend) during two previous decades. At the same time, the same features of the behavior of the aforementioned trend k(foE) are obtained. The trend is positive and negative in the morning and evening hours, respectively. Similar diurnal behavior of k(foE) is found also for Moscow station but with lower absolute values of the trends. A well-pronounced seasonal behavior of k(foE) is detected at Juliusruh and Slough: the trend is minimal and maximal in the summer period and at the end of fall—beginning of winter, respectively. The maximal amplitude in the morning hours reaches +0.04?MHz per year, whereas the minimal amplitude in evening hours is ?0.06?MHz per year. No systematic changes exceeding by the magnitude 0.01?MHz per year are found for Rome and Wakkanai stations. It is assumed that the observed trends are related to changes (trends) in the meridional wind bringing NO molecules from the auroral oval to lower latitudes.     

离散粗糙元诱发边界层转捩的实验研究

针对直升机转子叶片模型表面离散粗糙元诱发边界层转捩问题开展了实验研究,分析不同雷诺数下粗糙元尺寸参数对转捩位置的影响。实验在中航工业气动院直升机转子叶片模拟装置进行,在模型转子叶片表面布置不同尺寸的离散柱状粗糙元,利用红外热像技术探测边界层转捩,并提出一种基于湍流／层流区域面积比的转捩位置判定准则,目的是实现边界层转捩位置自动识别,进而分析粗糙元尺寸参数对转捩位置的影响。实验转速为300至600 r／m,对应叶尖切向速度为25～40 m／s。实现了对旋转叶片边界层转捩位置的定量测量,通过实验验证,转捩位置判定算法正确可靠,初步得到了不同高度 DRE 诱发转捩位置与雷诺数之间的关系,随着粗糙元高度的增加,转捩位置逐渐靠前。