基于精益6滓的航空高强钢零件大尺寸面轮廓度 数控加工参数优化

针对某航空高强钢零件大尺寸面轮廓度数控加工合格率较低问题,利用精益6σ方法,依据DMAIC的研究路径,充分运用箱线图、等方差检验、单因子方差分析等方法和工具,分析了“人、机、料、法、环、测”6大方面的操作者、加工刀具、装夹方式、主轴转速、切削量、进给速度、切削方式7个因素,确定刀具尺寸、切削量、进给速度为关键影响因素;通过建立面轮廓度与7个影响因素之间的GLM模型,得出影响流程输出的3个关键影响因素的最佳组合,并在此基础上对工艺参数进行优化。结果表明:该零件的数控加工工艺流程改进后,减少了加工过程中的人工调试检查环节,缩短了加工调试验证时间,大尺寸面轮廓度数控加工合格率从80%提高到96%以上,取得了较好的经济效益。     

数字示波器在尖峰干扰脉冲强度测量中的应用

运用数字示波器瞬态捕获能力及面积测量功能，快速、准确、不遗漏地测量电子设备的尖峰干扰信号（脉冲信号），用公式将脉冲强度单位换算为脉冲频谱密度单位。     

三叉杆式万向联轴器采用调心轴承时的运动分析

分析了三叉杆式万向联轴器采用调心轴承时输出转角和输入转角之间的关系式,并得出这种联轴器为准等角速传动万向联轴器的结论;讨论了轴偏转角大小对输出输入转角差值的影响,分析表明,这种联轴器中转角差值的变化周期是输入轴自转周期的3倍。     

机械连接件中螺栓孔角裂纹应力强度因子数值计算(英文)

The three-dimensional finite element method is used to solve the problem of the quarter-elliptical comer crack of the bolt-hole in mechanical joints being subjected to remote tension. The square-root stress singularity around the corner crack front is simulated using the collapsed 20-node quarter point singular elements. The contact interaction between the bolt and the hole boundary is considered in the finite element analysis. The stress intensity factors （SIFs） along the crack front are evaluated by using the displacement correlation technique. The effects of the amount of clearance between the hole and the bolt on the SIFs are investigated. The numerical results indicate that the SIF for mode I decrease with the decreases in clearance, and in the cases of clearance being present, the corner crack is in a mix-mode, even if mode I loading is dominant.     

结构比强度及其在优化设计中的应用

本文从结构重量角度推导了比强度(含比模量)表达式,分析了对同一材料不同比强度的关系,给出了比强度在结构动态分析中及结构优化设计中的应用。     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

不同深宽比陷窝诱导涡结构分析

陷窝所诱导的旋涡强化动量或热的交换,使得陷窝在分离流动控制和强化对流传热研究中很受关注。深宽比是影响陷窝诱导涡结构的重要参数,开展了深宽比对陷窝诱导涡结构影响的研究。研究发现,深宽比为0.06时,涡结构为马蹄涡;深宽比为0.1至0.14时,涡结构为闭式分离泡;深宽比为0.16至0.20时,涡结构为对称类龙卷风涡;深宽比为0.22至0.30时,涡结构为非对称类龙卷风涡。通过涡核涡强度对比发现,过深的陷窝和过浅的陷窝其内涡强度均比中等深度陷窝弱。     

高温长期时效对一种镍基单晶合金拉伸和持久性能的影响

研究了高温长期时效对一种镍基单晶合金在室温条件下瞬时拉伸强度和在950℃/240MPa条件下持久性能的影响。结果表明:1000℃短期时效100h,合金室温拉伸强度σb与屈服强度σ0.2与时效前相比没有明显变化,时效超过500h后σb和σ0.2开始显著下降,时效超过1000h后,σb和σ0.2随时效时间延长下降幅度减小;短期时效100h和500h样品在950℃/240MPa条件下的持久寿命大幅度降低,延伸率快速上升,时效时间超过1000h后,持久寿命的下降幅度减小,合金的持久寿命与延伸率均趋于稳定。长期时效后γ'相形貌改变及γ/γ'相界面高密度位错网的破坏是时效后合金室温及高温持久性能持续降低的主要原因。     

客机复合材料APU舱门结构设计及分析

按照结构布局、适航要求及APU门载荷水平,对复合材料APU舱门结构进行设计研究.为满足防火要求和闪电防护要求,选择先进碳纤维复合材料和泡沫芯材,设计了一种复合材料夹层结构.利用有限元模型对夹层结构在气动载荷和风载作用下进行应力和位移分析,得到应变云图和变形云图,分析说明该夹层结构设计满足设计要求.通过对B737飞机APU舱门结构研究和重量提取,进行重量等效对比分析,结果表明该复合材料夹层结构比金属结构重量轻25.8％,减重效果明显.