激光熔化沉积15-5PH沉淀硬化不锈钢组织及拉伸性能

利用激光熔化沉积技术制备15-5PH沉淀硬化不锈钢板,利用金相显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)技术,对沉积态组织进行分析,测试沉积态组织的室温拉伸性能。结果表明:激光熔化沉积15-5PH不锈钢沉积态组织由沿沉积增高方向贯穿多层外延生长的柱状晶组成,柱状晶内包含多个细长整齐排列的胞状树枝晶,枝晶内为马氏体组织,枝晶间为铁素体;沉积态组织中弥散分布大量细小的NbC析出相,尺寸12～20 nm;15-5PH不锈钢沉积态组织具有良好的力学性能,纵向抗拉强度和延伸率分别为1 128.5 MPa和14.0%,横向抗拉强度和延伸率分别为1 101 MPa和12.25%。     

折叠翼弹簧锁紧机构动力学仿真分析

基于刚柔耦合动力学理论,对折叠翼弹簧锁紧机构展开到位瞬时的碰撞问题进行分析,采用LS-DYNA建立折叠翼的刚柔耦合动力学模型,在各构件之间建立运动副和接触关系,对折叠翼展开到位时的局部接触碰撞动力学过程进行数值模拟。本文的建模方法更准确地计算了折叠翼展开到位的动力学响应,给出了折叠翼展开到位的碰撞特性,得到碰撞过程中折叠翼的应力分布。从而为折叠翼机构的设计提供指导。     

燃气轮机快速并车过程冲击及响应特性试验研究

为研究燃机快速并车过程中的冲击及响应特性,搭建并车试验台架,采用试验方法对并车参数和轴系部位对轴系动态响应幅值的影响开展研究。经过试验发现：快速并车过程中SSS离合器(同步自动换挡离合器)啮合瞬间会产生扭矩冲击,轴系因此产生明显的扭矩响应,并且相同的并车参数下扭矩响应的幅值会在一定范围内波动；降低并入机的设定扭矩或延长加载时间均可明显降低扭矩冲击和响应幅值；扭矩冲击对轴系不同部位产生的响应也不同,越靠近SSS离合器的位置,扭矩响应越大,且经过减速齿轮后响应明显降低。结果表明：所搭建的试验台架能够反映燃机快速并车过程中的冲击及响应特性,可为燃燃联合动力装置并车策略和安全性设计提供参考。     

穿孔泡沫夹层复合材料低速冲击性能试验研究

针对普通泡沫夹层复合材料层间性能较弱的问题，提出在泡沫上预先打孔的方法，在泡沫芯材中形成胶钉从而提高泡沫夹层材料的力学性能，并对穿孔泡沫夹层复合材料的低速冲击性能进行了研究。通过手糊和真空辅助成形工艺制备穿孔泡沫夹层复合材料试验件，对其进行不同能量的低速冲击试验，记录接触力、冲头位移和能量吸收率等力学响应，并采用目视检测和超声C扫无损检测两种方法确定冲击损伤的范围，探究胶钉密度、打孔深度和泡沫槽宽等变量对穿孔泡沫夹层复合材料低速冲击阻抗性能的影响。试验结果表明，随着冲击能量的增加，最大接触力、最大冲头位移和残余变形均增加，凹坑深度和内部损伤面积也增大，同时结构的能量吸收率也有所提高；适当地增加胶钉密度和泡沫槽宽能提高穿孔泡沫夹层材料的低速冲击阻抗性能，而泡沫孔深度对其冲击性能的影响较小。     

Macro-phenomenological high-strain-rate elastic fracture model for ice-impact simulations

The ice impact can cause a severe damage to an aircraft’s exposed structure, thus, requiring its prevention. The numerical simulation represents an effective method to overcome this challenge. The establishment of the ice material model is critical. However, ice is not a common structural material and exhibits an extremely complex material behavior. The material models of ice reported so far are not able to accurately simulate the ice behavior at high strain rates. This study proposes a novel high-precision macro-phenomenological elastic fracture model based on the brittle behavior of ice at high strain rates. The developed model has been compared with five reported models by using the smoothed particle hydrodynamics method so as to simulate the ice-impact process with respect to the impact speeds and ice shapes. The important metrics and phenomena (impact force history, deformation and fragmentation of the ice projectile and deflection of the target) were compared with the experimental data reported in the literature. The findings obtained from the developed model are observed to be most consistent with the experimental data, which demonstrates that the model represents the basic physics and phenomena governing the ice impact at high strain rates. The developed model includes a relatively fewer number of material parameters. Further, the used parameters have a clear physical meaning and can be directly obtained through experiments. Moreover, no adjustment of any material parameter is needed, and the consumption duration is also acceptable. These advantages indicate that the developed model is suitable for simulating the ice-impact process and can be applied for the anti-ice impact design in aviation.     

某型训练指挥台电源系统的优化设计

电源系统是为某型训练指挥台内部各设备提供能源支持的基础单元。通过对电源系统的组成结构和功能的系统分析,针对电源系统存在的 3个方面不足,包括:启动冲击电流过大、电源开关存安全隐患以及风扇组交流负载消耗不合理,提出相应的优化措施,即:应用软启动电源降低启动冲击电流、利用低压控制高压提高安全性、使用直流风扇替换交流风扇降低交流负载消耗。实际应用表明,在采用上述优化措施后系统的可靠性和安全性均得 到了明显提高,达到了优化的目的。