CFRP层板的落重冲击分层损伤研究

采用落重冲击试验方法研究了航空上常用的铺层形式为［Ｏ２／９Ｏ２／４５２／－４５２］ｓ的先进复合材料（ＣＦＲＰ）低能冲击损伤问题。重点讨论了落重冲击后分层损伤形貌、冲击能量Ｗ与分层面积Ａ之间的关系以及基体韧性对ＣＦＲＰ抗冲击性能影响。     

三维机身起落架着陆冲击力学模型

 本文根据起落架系统的几何、运动学及动力学特性,推导出目前广泛使用的三维机身式起落架,并具有柔性支柱系统的着陆冲击力学模型。并对其初始条件、对称着陆及不对称着陆情况作了动力学分析。     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

粉末高温合金FGH96惯性摩擦焊接头常温力学性能分析

第二代粉末高温合金FGH96是采用损伤容限设计思想研制的新型粉末高温合金,是当前750℃工作条件下满足高推比、高燃效发动机使用要求的涡轮盘、环形件和其他热端部件的理想材料.结合FGH96惯性摩擦焊接头的组织特征和强化相γ′数量分析接头的显微硬度和常温拉伸性能.结果表明,FGH96惯性摩擦焊接头具有良好的常温力学性能.     

机场跑道耐冲磨混凝土的研究

针对机场跑道混凝土所处环境、受力特环以及对修补材料的性能要求，提出采用超塑化、膨胀、树脂掺入等复合手段，大幅度改善钢纤维混凝土基质材料的结构性能。通过高效粘结，充分发挥了钢纤维的增韧抗冲击作用，使这种有机无机复合、金属非金属复合的混凝土材料具有优异的抗冲击性和耐磨性。实验结果表明，机场跑道混凝土特别是飞机起降区域板块适合采用SPE－SFRC复合材料。在基础稳定的条件下，基本可在设计使用年限内无须大修，其社会、经济效益巨大。     

数字全息测量超高速撞击碎片云实验研究

在中国空气动力研究与发展中心(CARDC)超高速碰撞中心(HIRC)7.6 mm超高速碰撞设备的基础上，搭建纳秒级脉冲激光数字全息系统。提出滤波片和衰减片组合布置，减弱超高速碰撞等离子体自发光、提高信噪比的方法。实验获得了2.25 mm铝球弹丸以4.0 km/s的速度撞击0.5 mm厚铝板形成碎片云的全息图。采用小波变换算法对碎片云全息图进行重建，得到超高速撞击碎片云的三维结构和碎片大小。碎片云的轮廓呈椭球型，分为碎片云的前端、核心和外壳，碎片主要分布在弹丸破碎形成的碎片云核心，存在大碎片，且分布较集中，对后板的损伤也严重     

基于纯比例导引的拦截碰撞角约束制导策略

拦截碰撞角约束制导是当前导弹制导研究的关键问题之一。首先基于理想比例导引（IPN）律拦截非机动目标的解析解,推导了纯比例导引律（PPN）拦截固定目标的解析解,得到了弹目相对距离、制导指令加速度和导弹前置角的显示表达式,并进一步得到了拦截碰撞角与弹目相对运动状态和比例导引系数之间的解析表达式。其次,基于该解析表达式,提出了基于PPN的拦截碰撞角约束制导策略（PPNIACG）,并探讨了在铅垂面内进行落角约束打击和水平面内进行拦截碰撞角约束打击的2种实现方式。最后,以弹道成型制导律（TSG）和最优碰撞角约束制导律（OIACG）为参考,通过数值仿真算例,对PPNIAC的拦截性能进行了对比分析,验证了所提出制导策略的有效性和正确性。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

直升机旋翼桨叶的弹性碰撞动力学建模

建立了直升机旋翼桨叶弹性正碰撞的动力学模型,采用有限转动梁理论处理桨叶的弹性变形,利用Hertz接触理论处理局部弹性变形,引入位移协调方程识别弹性碰撞载荷,运用Hamilton原理建立了桨叶正碰撞的动力学方程.通过与Timoshenko算例的对比表明了该方法的正确性,且对集中质量与直升机桨叶的弹性正碰撞问题进行了研究.      

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.