基于等效时间的混合储能系统高功率密度优化配置

越来越多的电力电子装置应用到多电飞机（MEA）电力系统中,导致MEA用电负荷功率呈现脉动特性,采用混合储能系统（HESS）平抑负荷功率脉动。为减少HESS重量,提出了一种高功率密度的优化配置方法。为建立负荷功率与储能介质之间的关系,提出了等效时间（ET）的概念,比较两者的ET常数作为储能系统类型选取的依据。进一步提出空间矢量法,采用能量型储能介质矢量和功率型储能介质矢量合成负荷功率,确定最优单体和截止频率,实现了HESS高功率密度配置。同时,从能量约束和功率约束两个方面进行HESS的容量的计算。最后,通过算例配置和仿真分析验证了本文所提方法的可行性和正确性。     

Flow field characteristics,mixing and emissions performance of a lab-scale rich-quench-lean trapped-vortex combustor utilizing a quench orifice plate combined with a bluff-body

In this study, the low emission combustion technology of Rich-Quench-Lean (RQL) has been applied in Trapped-Vortex Combustor (TVC), and the combinative RQL-TVC shows a promising low emissions performance. By utilizing a quench orifice plate combined with a bluff-body, a lab-scale RQL-TVC was designed. The flow fields of RQL-TVC were measured by 2-D PIV and predicted by 3-D numerical simulation. Flow structures, radial profiles of normalized mean axial velocity, turbulence intensity and mixing level of the quench zone were analyzed. Results reveal that the dual-vortex and the single-vortex flow patterns both exist in cavities and quench zone of RQL-TVC, and the turbulence intensity is strong in the quench zone with some reverse flows. The spiral vortex was discussed by 3-D streamlines and the detail flow structures of the quench zone were analyzed based on the numerical results. The mixing level of the quench zone was determined, and results show that the quench device enhances the mixing level compared with TVC. Combustion efficiency and emissions performance were investigated experimentally, and results demonstrate that RQL-TVC has relatively higher combustion efficiency and lower emission index of CO, UHC and NO_x than the same size lab-scale TVC in present work.     

叠层穿刺CF/Al复合材料准静态拉伸力学行为与失效机制

针对新型的叠层穿刺碳纤维织物增强铝基复合材料（CF/Al复合材料）,通过细观力学数值模拟与实验结合的方法研究了其在准静态拉伸载荷作用下的渐进损伤与断裂力学行为。复合材料经向拉伸弹性模量、极限强度与断裂应变的实验结果分别为129.61 GPa、630.14 MPa和0.75%,细观力学模型预测误差分别为-9.41%、7.57%和1.33%,均匀化计算的宏观应力-应变曲线与实验曲线总体上相符。经向拉伸变形初期首先出现经/纬纱交织处基体合金的局部损伤,随着拉伸应变量的增大依次发生纬纱和穿刺纱的横向开裂,拉伸变形后期基体合金与经纱失效引起宏观应力-应变曲线的急剧下降,复合材料拉伸断口表现为经纱轴向断裂及纬纱和穿刺纱横向开裂共存的形貌特征,纤维拔出和基体断裂导致的经纱轴向断裂是诱发复合材料最终失效的主要机制。     

低温泵常见故障分析及其解决措施

文章对低温泵运行过程中所发生的冷头及氦压缩机典型故障进行了原因分析,并提出了解决措施。最后提出了使低温泵可靠稳定运行的建议。     

Applications of tuned mass dampers to improve performance of large space mirrors

In order for future imaging spacecraft to meet higher resolution imaging capability, it will be necessary to build large space telescopes with primary mirror diameters that range from 10 m to 20 m and do so with nanometer surface accuracy. Due to launch vehicle mass and volume constraints, these mirrors have to be deployable and lightweight, such as segmented mirrors using active optics to correct mirror surfaces with closed loop control. As a part of this work, system identification tests revealed that dynamic disturbances inherent in a laboratory environment are significant enough to degrade the optical performance of the telescope. Research was performed at the Naval Postgraduate School to identify the vibration modes most affecting the optical performance and evaluate different techniques to increase damping of those modes. Based on this work, tuned mass dampers (TMDs) were selected because of their simplicity in implementation and effectiveness in targeting specific modes. The selected damping mechanism was an eddy current damper where the damping and frequency of the damper could be easily changed. System identification of segments was performed to derive TMD specifications. Several configurations of the damper were evaluated, including the number and placement of TMDs, damping constant, and targeted structural modes. The final configuration consisted of two dampers located at the edge of each segment and resulted in 80% reduction in vibrations. The WFE for the system without dampers was 1.5 waves, with one TMD the WFE was 0.9 waves, and with two TMDs the WFE was 0.25 waves. This paper provides details of some of the work done in this area and includes theoretical predictions for optimum damping which were experimentally verified on a large aperture segmented system.     

翼型前缘变形对动态失速效应影响的数值计算

翼型或机翼的动态失速效应所引起的低头力矩和正气动阻尼限制了飞行器气动性能的提高,甚至可能诱导发生不稳定运动。应用于小尺寸机翼的前缘动态变形（DDLE）技术,通过实时改变前缘形状,能够改善翼型前缘区域的速度梯度,进而抑制动态失速效应。采用转捩剪切应力输运（SST）黏性模型结合分区混合动态网格技术,研究了这种前缘变形对机翼俯仰运动所引起的非定常流动的影响,得到通过小幅度前缘变形抑制和延迟动态失速的方法,从而提高翼型的气动性能。翼型NAC A0012的数值模拟结果与动态失速风洞试验结果比较表明：所使用的数值计算方法能够较为准确地模拟翼型在动态失速过程中升力系数与俯仰力矩系数的变化情况,可用于研究前缘变形对翼型俯仰运动所引起的非定常流动的影响。前缘动态变形翼型俯仰运动过程的非定常流场的数值模拟表明：在大迎角下不同幅度的前缘下垂运动能够抑制流动分离的发生,从而抑制动态失速,但在大迎角下小幅度高频率的前缘下垂变形能更高效地抑制动态失速;前缘变形幅度以及变形沿中弧线的分布对升力系数和俯仰力矩系数的影响并不明显。     

铝合金薄板零件橡皮囊成形屈曲分析与实验

为了抑制铝合金薄板类零件在橡皮囊成形后出现屈曲的缺陷,采用薄板屈曲微分方程对零件成形后的屈曲进行理论分析,并通过橡皮囊成形实验研究自然时效时间和成形压力对屈曲缺陷的影响。理论分析结果表明：零件法兰屈曲波数与其内外径比有关,通过改变法兰宽度进行实验验证,实验结果与理论分析结果相符;而成形实验结果表明,屈曲缺陷高度随板料自然时效时间的增加而增加,随成形压力的增加而减少。因此,理论分析结果有效,并且可通过减少淬火后成形时间和增加成形压力来抑制屈曲缺陷。     

简化的混合估计算法及其在GPS／SINS深组合中的应用

为解决GPS/SINS深组合导航系统滤波的非线性和噪声的不确定性的问题,针对深组合模型特点,设计了一种简化的基于U滤波的多模型混合估计滤波器。根据系统模型中状态方程是线性方程、观测方程是非线性方程的特点,提出了一种简化的U滤波算法(Ultra tight coupling unscented Kalman filter,UTCUKF),然后针对噪声变化建立了非线性模型,多模型混合估计滤波器的输出为各滤波器的概率加权融合,因此模型概率是根据噪声变化而调整的,从而也使系统输出对噪声变化具有一定自适应能力。最后进行了仿真,并与基于普通U滤波的多模型混合估计算法进行了比较。结果表明,本文算法的解算时间短,模型切换速度更快,而估计的精确度与同条件下的基于普通U滤波的多模型混合估计算法相当,更符合深组合系统高动态的要求。     

带多孔板的APU进气系统气动性能实验

利用实验方法对一类带多孔板的辅助动力装置(APU)进气系统气动性能进行了研究.实验结果表明:两出口的总压恢复系数和总压畸变指数均随流量的增加不断降低.总压恢复系数在定总流量时略微下降,在定配比时几乎线性下降.总压畸变在周向上主要受多孔板无孔区影响,径向上主要受流道曲率影响.随开孔率增加,总压恢复系数不断增加.动力端不同开孔率下,总压畸变以径向畸变为主,负载端在小开孔率时以周向畸变为主,大开孔率时径向畸变成为主要因素.      

前级环形切割器对后端靶板影响的数值仿真

利用ANSYS／LS—DYNA软件进行了环形切割器爆炸后对后端靶板的毁伤及环形切割器壳体的破裂过程的数值仿真。仿真结果表明：环形切割器爆炸后对后端靶板的毁伤中,起主璎作用的是环形切割器壳体的端部形成的破片和内侧形成的聚能侵彻体,而聚能侵彻体对靶板的破坏最为严重;琏于环形切割器的串联战斗部设计中,需考虑两级战斗部隔爆设计。