定/变热线过热比跨超声速流场湍流度测量

开展了基于定、变热线过热比方法测量跨超声速流场湍流度的比较研究,以满足高速飞行器与发动机的跨超声速风洞高精度实验需求。在1.2 m暂冲式跨超声速风洞上,采用定过热比、变二过热比和变八过热比等三种热线测量方法,完成了马赫数为0.30~4.25的跨超声速流场湍流度测量研究。测量结果表明：变八过热比测量精度最高,实测湍流度的蒙特卡洛模拟不确定度为0.001%~0.033%;定过热比方法与变二过热比方法可实现更快速的测量,在马赫数为0.40~2.00范围内与变八过热比测量湍流度均值偏差约9%~18%。研究结果对跨超声速流场湍流度校测、飞行器实验鉴定和数值计算具有实际助益。     

应用少量短电阻应变丝布置的损伤评估智能材料结构

智能材料结构是一门新学科，它越来越引起不同学科研究者们的兴趣，本文研究采用电阻应变丝为传感元件，人工神经网络为处理辨识器的损伤评估智能材料结构，提出并实施了一种少量短电阻应变丝的传感元件布置方法，用以对结构中损伤或大应变的区域和级别进行在线评估。     

热线风速仪在紊流流场测量中的应用

本文综合分析了目前采用热线风速仪测量紊流流场的各种方法,并着重指出,在高紊流度情况下,还没有比较可靠的方法。在使用目前推荐的各种计算公式时,必须首先验证其公式的可靠性,并注意其限制性条件。     

某型涡轮螺桨发动机转子偏磨故障分析

 某型涡轮螺桨发动机曾发生过多起转子偏磨故障,工厂对此作过许多分析,本文在其基础上再对该项故障的原因和机理结合实际地作了进一步的比较、分析和论证,提出了排故措施。效果显著。     

37mm冲压加速器热发射试验初步结果

气动中心超高速所自行研制成国内第一座冲压加速器，并成功地实现了弹丸的冲压加速。文中首先给出冲压加速器的工作原理、国内外研究现状，以及３７ｍ ｍ 口径冲压加速器系统组成，最后给出了热发射不起动（ｕｎｓｔａｒｔ）和热发射实现冲压加速的初步结果     

Relationship Between Corrosion Level of Steel Bar and Diameter of Corroded Sensing Steel Wire in Wireless Sensor

A kind of wireless sensor was previously developed,which is powered and transmit signals wirelessly instead of using an electrical connection to the embedded reinforcement.Based on this technique,the relationship between diameters of corroded sensing steel wires and corrosion levels of steel bars is established by experiments.Quadratic function is utilized to fit the experiment results,and the correlation coefficients are all larger than 0.95.Estimated corrosion levels of commonly used steel bars are given for different diameters of corroded sensing steel wires fractured due to corrosion.     

Numerical investigation on flow field characteristics of dual synthetic cold/hot jets using POD and DMD methods

In order to improve the control ability of synthetic jets in compressible boundary layer, a novel control method based on dual synthetic cold/hot jets coupled control of velocity profile and temperature profile was proposed. As fundamental investigations on the effects of synthetic jet temperature on the jet behavior and flow field characteristics were essentially necessary, preliminary numerical simulations were conducted to study the influence of temperature (200 K and 400 K) on the flow field characteristics of synthetic jets using Large Eddy Simulations (LES) model. Time-averaged flow fields showed that different temperatures led to variable behavior of two strands of jets. For dual synthetic cold jets, a potential-core arose apparently with its height ranging from 0.01 to 0.03 m, while for dual synthetic hot jets, two strands of jets emerged downstream. The modal decomposition of instantaneous flow fields had been done using both Proper Orthogonal Decomposition (POD) and Dynamic Mode Decomposition (DMD). Various modes showed different characteristics of the flow fields. As the POD method focuses on the energy of flow while the DMD method focuses on the frequency, the first two modes had many similarities, but the third and fourth modes demonstrated completely different vortex structures. The current researches play a role of preliminary investigations for further and comprehensive exploration of novel flow control measures in global velocity field.     

电渣重熔连续定向凝固René88DT合金的组织与热变形行为

自行设计开发了适合工业化生产高纯净,低偏析,无宏观缺陷铸锭的电渣重熔连续定向凝固技术(ESR-CDS)的设备和工艺,利用该技术成功制备了直径为φ150mm的René88DT合金定向凝周铸锭.采用XRD测试了定向凝固柱状晶的生长取向,结果表明,ESR-CDS René88DT铸锭柱状晶择优生长方向为<100>系晶向;ER...     

特型钝体绕流动态特性的低速实验研究

在低速自由射流风洞上 ,利用热线及相关设备对由半球头部、颈部及旋成体构成的特型钝体周围非定常流动的基本特性、联合特性及湍流度分布进行了测试与分析 ,实验工况为迎角α=- 1 5°～ 1 5°、侧滑角 β =0°～ 1 0°。结果表明 ,在上述工况范围内 ,该钝体周围流场中速度脉动的能量分布平坦 ,属宽频带随机信号 ,流场中没有发生明显的流动分离 ,流场动态品质良好 ;凹陷区内气流的脉动以不同的速度向下游空间传播 ;在上述α、β变化范围内 ,钝体颈部凹陷区的最大湍流度高达 1 0 .9～ 2 4.8%。     

热等静压处理对定向凝固NiAl/Cr(Mo,Hf)合金沉淀相和高温拉伸性能的影响

 研究了经热等静压处理后定向凝固 Ni Al/Cr(Mo,Hf)合金中的沉淀相和高温拉伸性能的变化。通过透射电镜和扫描电镜观察发现 :热等静压处理后,Ni Al和 Cr(Mo)相的形貌变化不大,聚集在 Ni Al/Cr(Mo)相界上的 Heusler减少并在 Ni Al,Cr(Mo)相中重新分布。从界面能的角度解释了 Heusler相主要沉淀在Ni Al/Cr(Mo)相界上的原因。热等静压处理后合金中不存在 G相。高温瞬时拉伸实验表明此合金具有优异的高温拉伸强度。