基于声发射信号的高速铣削过程监测技术

叙述了如何将声发射技术应用于航空铝合金的高速铣削过程监测,介绍了监测装置硬件系统和信号数据采集平台的构成,最后运用小波分析进行信号分解,计算分解后的各频段能量,并从频段的能量对比中发现,信号能量可以作为刀具磨损的特征参数.     

原位自生TiB_2/Al-7Si复合材料组织和性能

采用混合盐法制备了原位自生TiB2 颗粒增强Al-7Si复合材料.扫描电镜观察结果表明,制备的原位TiB2 颗粒分布均匀,其最大尺寸在900nm左右,平均尺寸在 400nm 左右.TiB2 颗粒对a-Al 和共晶si都具有显著的细化效果.其复合材料的力学性能和干摩擦磨损性能较其基体有明显的提高.     

高强钢铣削中微量润滑技术效果的试验分析

为了验证微量润滑技术对刀具磨损及工件表面粗糙度的影响,研制出一套微量润滑系统,利用压缩气体流经的截面变小所产生的压强差来吸取箱体中的液体,并传输到喷嘴进行雾化.将其应用在高强度钢铣削加工中.试验结果表明:相对于干切削和传统浇注冷却,微量润滑技术具有明显的优势,它可有效地减小刀具磨损,并将工件表面粗糙度控制在较低的水平,尤其在高转速、大切深、快进给加工中,同时其还具有结构简单、冷却液用量小、对环境污染小等优点.对试验结果进行了初步分析.     

基于域对抗门控网络的变工况刀具磨损精确预测方法

刀具磨损的精确预测对保证零件加工质量、提高生产效率和降低制造成本具有重要作用。在实际加工过程中,切削参数、刀具几何参数、刀具材料等工况复杂多变,工况信息和刀具磨损量对监测信号的耦合作用为刀具磨损的精确预测带来了很大挑战。针对以上问题,提出了一种基于域对抗门控网络（DAGNN）的变工况刀具磨损精确预测方法。引入工况分类网络并利用无磨损量标签样本,通过域对抗和门控过滤机制自适应地从不同工况的原始监测信号中提取表征刀具磨损且对工况变化不敏感的关键信号特征。对信号特征提取网络和刀具磨损预测网络进行迭代优化,从而实现变工况刀具磨损的精确预测。实验结果表明：相比已有的方法,本文方法能够利用少量带磨损量标签的目标工况样本实现刀具材料和刀具直径变化情况下的刀具磨损量精确预测,预测精度大幅提高。     

Performance evaluation of creep feed grinding of γ-TiAl intermetallics with electroplated diamond wheels

This paper evaluates the performance of creep feed grinding γ-TiAl intermetallic (Ti-45Al-2Mn-2Nb) using electroplated diamond wheels. Firstly, a comparative analysis with the grinding results by using electroplated CBN wheels was conducted, mainly involving abrasive wheel wear behavior and maximum material removal rate below surface burn limit. It was found that the diamond wheel would produce much better grinding results including lower wheel wear rate and higher maximum material removal rate. Then the surface integrity obtained at different level of material removal rate was characterized with the utilization of the diamond wheel. The poor ductility of this γ-TiAl intermetallic material was found to have a marginal effect on the surface integrity, as no severe surface defects such as material pullout were generated during the stable wheel wear stage. For the involved operating parameters, a deformation layer was produced with ∼10 μm or more in thickness depending on the material removal rate used. Meanwhile, a work-hardened layer extending to more than 100 μm was produced with a maximum microhardness of above 520 HV_0.05 (bulk value 360 HV_0.05). The residual stress remained compressive, with a value of above −100 MPa and even up to −500 MPa for an elevated material removal rate. Shearing chip was the main chip type, indicating good wheel sharpness in the grinding process.     

Tool Materials Rapid Selection Based on Initial Wear

Based on a large amount of literature about tool wear research, 873 tool wear curves are taken as samples, and statistical analysis is carried out to select the most suitable tool from all the tool materials suggested by the tool manufacturers. Statistical relationships between the initial wear and uniform wear periods are obtained. The results show that there is qualitative relationship between wear rate during initial wear period (WRIWP) and wear rate in uniform wear period (WRUWP) to certain extent. On this basis, a tool material rapid selection method based on the initial wear is put forward, and suitable tool materials for machining titanium alloy are selected. The experimental results indicate that this method is effective and useful. The new tool materials rapid selection can be used to select suitable cutting tool materials quickly before carrying out systematic machinability tests with the most suitable tool materials. The technology can be applied to doing the initial selection of cutting tool materials in either the machinability research or the workshop production.     

内氧化制备A1_2O_3/Cu复合材料载流条件下表面磨损形貌和摩擦学性能研究(英文)

Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and copper against brass are investigated and compared. The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope （SEM） and energy dispersive X-ray spectrum （EDS）. The results show that the wear resistance of the Al2O3/Cu composites is superior to that of copper under the same conditions, Under a given electrical current, the wear rate of Al2O3/Cu composites decreases as the Al2O3-content increases, However, the wear rates of the Al2O3/Cu composites and copper increase as the sliding speed and pressure increase under dry sliding condition. The main wear mechanisms for Al2O3/Cu composites are of abrasion and adhesion; for copper, it is adhesion, although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

涂层刀具铣削加工300M钢的刀具磨损试验研究

建立了一套便携式的在线刀具磨损图像检测装置及相应的计算程序,利用该装置观察到了涂层硬质合金刀具加工300M高强度钢过程的定性磨损规律,并确定了刀具磨损量的测量方法。     

微动损伤的研究综述

论述了微动损伤的概念及对其研究的必要性。对微动损伤研究的两个主要部分即微动损伤的基础研究和防护方法的发展过程进行了论述,尤其对当前的研究现状及所取得的成果做了重点阐述,并说明了一些尚待研究的问题。从微动机理研究、微动件结构参数控制、微动疲劳寿命估算、工业应用、防护等几个方面概述了微动损伤研究的发展趋势。     

磨粒磨损对砂带磨削TC17表面完整性的影响研究

砂带磨粒磨损直接影响磨削表面质量进而影响构件综合服役性能.以表面完整性为评估指标,对砂带磨损前后钛合金的表面加工质量进行了试验研究,揭示了砂带磨粒磨损对磨削TC17表面粗糙度、残余应力和表面硬度的影响规律及机制.结果表明,磨粒磨损后由于高度均匀化、单位面积切削磨粒数增加、磨削深度减小,使得表面粗糙度减小、纹理均匀细腻,...