“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

含金属纳米线多孔铝膜微偏振器的研究

含金属纳米线的多孔铝膜在近红外光区表现出较好的偏振特性。基于金属线栅偏振器的偏振原理,从金属纳米线对不同方向偏振光的消光机理出发,构建了以一排纳米线为研究对象的理论模型,分别计算了电矢量平行于纳米线轴向的偏振光（P）和电矢量垂直于纳米线轴向的偏振光（S）垂直入射时的光学损耗。在入射光波长固定的条件下,得到了P分量光、S分量光的透射率与模板孔径的关系。     

低雷诺数下小展弦比机翼的气动力优化设计

以固定翼式微型飞行器为研究背景,针对小展弦比机翼,将遗传算法与Navier-Stokes方程数值解法相结合,提出了一种以实数编码为基础的数值优化模型.流场数值模拟采用人工压缩方法,遗传算法采用锦标赛选择、自适应交叉和变异操作算子,对微型飞行器机翼选取五个设计点分别进行了升阻比优化设计.优化结果表明,本文的优化模型具有较高的搜索效率和显著的优化效果,五个设计点机翼的升阻比均提高30%以上.优化后的翼面接近椭圆形状,翼型前缘钝厚,尾缘向上拱起,这种形状能大大增加升力,降低诱导阻力,从而显著提高机翼的气动性能.     

多目标跟踪的核粒子概率假设密度滤波算法

提出一种新的多目标跟踪算法：核粒子概率假设密度滤波算法(KP-PHDF)。算法的创新点在概率假设密度滤波算法(PHDF)的目标状态提取步骤,以粒子概率假设密度滤波算法为框架,并运用结合了mean-shift算法的核密度估计(KDE)理论进行概率假设密度(PHD)分布的二次估计、提取PHD峰值位置作为目标状态估计值。分析与多目标跟踪(MTT)仿真的结果表明,与现有序列蒙特卡罗概率假设密度滤波算法（SMC-PHDF）相比,在相同仿真条件下新算法的估计精度提高30.5%。     

一种弧齿锥齿轮传动性能优化方法

 以期望的传动误差曲线为目标,首次提出了弧齿锥齿轮传动误差曲线优化的泛变性(GMR)方法,它是对局部综合法的一种改进。首先讨论了齿面接触印痕和传动误差曲线的计算方法,并在传统局部综合法基础上提出了泛变性局部综合法,给出了该方法的理论基础即局部综合公式和齿面接触方程,接着分析了对弧齿锥齿轮传动性能尤其是传动误差影响最大的两个加工参数即小轮切削速比和三阶变性系数的变化规律,最后对某具体航空弧齿锥齿轮副的传动误差曲线和齿面接触印痕进行了泛变性优化设计。结果表明：当小轮切削速比取0621 9且三阶变性系数取-0021 99时,轮齿接触分析(TCA)实际传动误差曲线比较对称且与期望曲线较好地吻合,而齿面接触印痕几乎没有变化,由此证明泛变性法对传动性能控制的有效性和稳定性。该研究工作对于航空齿轮传动系统具有重要的实际意义。