Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

石墨填料对浸渗热解-熔融浸渗方法制备的C/SiC复合材料结构和性能的影响

采用石墨树脂浆料浸渍三维针刺碳毡增强体,热解后得到C/C多孔体,并采用反应熔体浸渗法制备C/SiC复合材料.研究了石墨填料对C/C多孔体的结构以及C/SiC复合材料力学性能的影响.结果 表明,石墨树脂浆料浸渍时树脂填充束间小孔形成结构致密的亚结构单元,而石墨可以有效填充胎网层等大孔隙,一次浸渍热解后碳产率有效提高.所得...     

三维角联锁结构复合材料等效弹性性能有限元分析

在复合材料承载时变形协调的前提下,采用CAD软件绘制三维织物单元体几何模型,然后导入结构分析有限元软件包,对工程中常用的带衬经三维角联锁结构复合材料的弹性性能进行分析,并将0°和90°方向弹性性能预测值及实验值与取向平均法预测值进行比较。结果表明,采用的有限元方法所得预测值及实验值与取向平均法预测值之间具有很好的一致性。     

PP／SCF复合材料的制备和力学性能的研究

本文制备了聚丙烯（PP）／,短炭纤维（SCF）复合材料并研究了其力学性能。结果表明,复合材料的拉伸强度随SCF含量的增加有先增加后趋于稳定的趋势,当SCF含量达到6％时,拉伸强度达到极值。随着SCF的加入,冲击强度呈先增加后略有降低的趋势,复合材料在SCF含量为6％时冲击强度达到极值。由此可知,适量的加入SCF对PP起到了较好的增强增韧效果。     

基于全局Newton-Raphaon方法的弹流润滑分析

基于全局Newton-Raphaon方法对滑动轴承的弹流润滑性能进行了数值摸拟。比较了弹性变形对连杆大头轴承最小油膜厚度和最大油膜压力的影响。结果表明:全局Newton-Raphaon方法很好的解决了收敛困难,程序运行时间长的问题;考虑表面弹性变形的连杆大头轴承与刚性轴承相比,最小油膜厚度与最大油膜压力的变化趋势相同;一个工作循环内,弹性轴承的最小油膜厚度略大于刚性轴承,而最大油膜压力则明显减小。     

POSS 催化剂改性氰酸酯复合材料的性能

通过POSS 催化剂改性氰酸酯树脂,并采用热熔法排布制备了碳纤维/ 中温固化氰酸酯预浸料, 验证了改性氰酸酯的工艺性。同时考察了氰酸酯树脂及其复合材料的性能。结果表明, POSS 催化剂的加入, 降低了氰酸酯的固化温度,同时其使用温度、室温及-18℃的储存性能和复合材料力学性能与改性前相当。     

Performance of a small and low-cost chamber to simulate lunar surface environment

The performance of a small and low-cost metal chamber built to simulate the pressure and temperature conditions of lunar surface was assessed and the results are presented. This chamber is intended for studying the physical properties of lunar surface and subsurface (using soil simulants) and also to validate the technology readiness of certain newly developed payloads planned for future lunar surface missions (Lander/Rover). It is possible to reach down to ∼10⁻⁷ Pa under specific conditions and maintain the temperature of the sample under investigation to lunar day and night temperatures. The designed system has been subjected to various tests to evaluate its performance and suitability for carrying out experiments in a simulated lunar environment.     

新型电工钢片磁性能无损检测传感器及应用

介绍了一种新型电工钢片磁性能无损检测传感器及其测量原理 ,同时讨论了该传感器的设计原则并给出了典型数据及仿真测试结果     

2. 5D 衍生结构SiO2 f / SiO2 复合材料的经向力学性能

以几种不同的2.5D衍生结构织物为增强体,制备了法向增强、经向增强及经法向增强2.5D Si O2f/Si O2复合材料,比较了上述材料与现有2.5D Si O2f/Si O2复合材料的经向力学性能,并研究了经法向增强2.5D结构复合材料中增强纱比例、纤维体积分数与材料性能之间的关系,对织物结构进行了优化。结果表明,经法向增强2.5D Si O2f/Si O2复合材料的经向力学性能较现有2.5D复合材料有显著提高,该材料在较低密度下(1.6 g/cm3),经向拉伸强度与现有材料(1.65 g/cm3)持平,且经向压缩强度接近现有材料的4.3倍。     

酚醛树脂炭的合成及力学性能研究

为了表征多孔炭泡沫材料基体的结构与力学性能,采用碱催化法制备热固性酚醛树脂,经固化、高温炭化处理合成多孔炭泡沫材料的基体——酚醛树脂炭。研究酚醛树脂炭的微观结构、压缩强度及压缩断裂韧性。结果表明:酚醛树脂炭结构以树脂炭基体、微孔和微裂纹为主,其碳元素以sp3杂化的非晶炭形式存在;压缩强度为8.58 MPa,压缩断裂特征为脆性断裂模式;酚醛树脂炭的压缩断裂韧性较差,断裂过程中吸收的总能量为0.135 MJ/m3。