月面巡视探测器动力学建模

动力学模型是研究星球探测车运动的基础。以某月面巡视探测器原理样机为背景,建立了其动力学模型,并进行了数值仿真分析。在说明月壤机械特性的基础上,结合地面车辆力学的知识,分析了松散月壤上刚性车轮的受力,考虑了主动驱动和被动驱动的情形,利用数学拟合的方法得到了满足工程要求的简化模型。在一定假设条件下,以牛顿欧拉法建立了三自由度整车动力学模型,建模时同时考虑了驱动和转向的相互影响。最后,数值仿真结果定性地验证了月面巡视探测器动力学模型的正确性。     

频率选择表面传输特性的温度循环效应

根据国家军用标准GJB 150-86对不同涂层材料和加工工艺的频率选择表面(FSS,Frequency Selective Surfaces)进行了温度循环的环境模拟试验,通过比较温度循环前后FSS的谐振频率、传输损耗、频带宽度和入射角稳定性等传输特性的差异,考察FSS在温度循环条件下的性能稳定性.结果表明,温度循环对不同材料和工艺的FSS的传输性能有较大影响,主要表现在FSS的传输损耗和频带宽度两方面.不同FSS在经过温度循环后,谐振频率下的传输损耗增大0.5~3倍,入射角越大增大的幅度越大;频带宽度增加50%~70%,不同的FSS增加的幅度不同.而对谐振频率和入射角稳定性的影响根据不同的FSS而不同,但对二者的影响都不明显.与简单振子FSS相比,组合振子FSS的传输性能受温度循环的影响较大.      

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

大展弦比飞机运动稳定性建模及分析

随着飞机设计技术的提高和新型材料的应用,现代飞机气动弹性效应越来越显著,刚体运动和弹性体振动互相解耦的关系不再明显,在分析弹性飞机相关问题时,应该综合地、统一地考虑飞行动力学与气动弹性力学问题。本文在一般体轴系下综合考虑了飞机刚体运动自由度和弹性振动自由度,建立弹性飞机刚弹耦合运动的方程,通过在配平状态下引入小扰动运动假设,以及利用有理函数拟合技术将偶极子格网法计算所得到的频域非定常气动力转化为时域形式,建立了大柔性飞机刚弹耦合小扰动状态空间方程,并对纵向运动稳定性进行分析计算。针对文中构型飞机,运用本文所采用的方法计算所得结果与传统的线性及刚体计算所得结果进行对比分析,非线性计算方法所得颤振速度更小,而且失稳模态亦发生变化,对于飞行力学模态而言,长周期模态稳定性变差,在计算速度范围内出现失稳的现象,由此说明机翼大变形对飞机稳定性所带来的影响。     

含硅芳炔树脂改性氰酸酯树脂的性能

将双酚E型氰酸酯(BEDCy)与含硅芳炔树脂(PSA)用溶液共混的方法制备了共混树脂(BEDCy/PSA);通过DSC和原位红外研究了共混树脂的固化反应,使用TGA和DMA表征了树脂的耐热性能;还考察了共混树脂的介电性能和力学性能.结果表明,PSA树脂能够降低BEDCy树脂的固化温度;随着PSA树脂的添加,氮气和空气氛...     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

弹性支撑条件下裂纹齿轮体有限元模拟与仿真

将齿轮与轴的装配支撑关系考虑为弹性支撑, 采用有限元数值分析ANSYS软件对故障齿轮的动力特性进行了模拟.研究了裂纹故障发生后齿轮动力特性的变化, 分析了不同大小和不同类型的故障对齿轮体动力特性的影响.结果表明:裂纹的大小和位置对动力特性都有影响, 但裂纹发生位置的影响要大于裂纹大小的影响, 即处于齿轮结构体中部的缺陷要比处于外边缘的缺陷对动力特性影响大.另外, 探讨了仿真时设置弹性支撑边界条件的方法, 并通过与固定支撑和自由支撑边界条件的比较, 给出了弹性支撑条件下分析结果的真实性和有效性, 为齿轮故障发生机理和诊断的研究提供了一种方法.      

SIMULATION OF COMPOSITE NON-LINEAR MECHANICAL BEHAVIOR OF CMCS BY FEM-BASED MULTI- SCALE APPROACH

The non-linear behavior of continuous fiber reinforced C/SiC ceramic matrix composites （CMCs） under tensile loading is modeled by three-dimensional representative volume element （RVE） models of the composite. The theoretical background of the multi-scale approach solved by the finite element method （FEM） is recalled first- ly. Then the geometric characters of three kinds of damage mechanisms, i.e. micro matrix cracks, fiber/matrix interface debonding and fiber fracture, are studied. Three kinds of RVE are proposed to model the microstructure of C/SiC with above damage mechanisms respectively. The matrix cracking is modeled by critical matrix strain en- ergy （CMSE） principle while a maximum shear stress criterion is used for modeling fiber/matrix interface debond- ing. The behavior of fiber fracture is modeled by the famous Weibull statistic theory. A numerical example of con- tinuous fiber reinforced C/SiC composite under tensile loading is performed. The results show that the stress/ strain curve predicted by the developed model agrees with experimental data.     

ZnO透明导电薄膜制备及紫外辐照处理特性研究

ZnO作为一种典型的透明导电氧化物（Transparent conductive oxide,TCO）材料,具有同氧化铟锡(Indium tin oxide,ITO)相比拟的光电性能,其原料丰富、绿色环保、易于制备、生成成本低等优点使ZnO成为最有希望替代ITO的材料。本文以玻璃为衬底,利用量子点种子层作为缓冲层,采用传统水热方法制备了低成本ZnO透明导电薄膜,采用特殊的紫外光辐照工艺对薄膜进行后处理,探索薄膜生长参数和紫外光辐照处理工艺对其透光率和导电性的影响。结果表明,紫外辐照处理不影响薄膜的透光性能,而使材料的方块电阻降低3个数量级,数值从没处理时的1.5×105 Ω/□降低到 150 Ω/□,极大地提高了薄膜的电导率,为ZnO薄膜材料电导率的提高提供了一个简单高效的途径。     

含炔基有机硅杂化聚合物的合成及热稳定性

采用双乙炔基封端的硅氮烷单体(双(4-乙炔基苯胺基) 二苯基硅烷,M1) 与含不同二甲基硅基
结构单元[—Si( CH3 )2—,—Si( CH3 )2—O—Si( CH3 )2—和—Si( CH3 )2—O—Si( CH3 )2—O—Si( CH3 )2—] 的
双溴苯基封端单体进行Sonogashira 交叉偶联反应,制备出一系列含炔基有机硅杂化聚合物。通过红外( FTIR)
、核磁氢谱(1H-NMR) 和凝胶渗透色谱( GPC) 对聚合物的结构和分子量进行了表征,并采用热重分析
(TGA)对聚合物的热性能进行了研究。结果表明,二甲基硅基结构的引入显著提高聚合物的溶解性,各组聚
合物均展现出良好的热稳定性能,其中引入—Si(CH3)2—结构的聚合物具有相对最好的热稳定性。