不同类型多级等离子体激励器诱导气流的力学特性研究

等离子体激励器通过产生的等离子加速气流,可以实现对流动的控制。单级等离子体激励器由于受到等离子体放电的物理限制,其控制作用较小;为了提高等离子体流动控制的效果,关于多级等离子体激励器的研究得到发展。采用图像采集和粒子示踪测速系统(PIV),对传统多级等离子体激励器和多级双极性等离子体激励器的放电现象以及气流加速进行研究,并通过流场速度分布计算等离子体激励器对空气产生的推力和吸力。结果表明:随着电压的升高,传统多级等离子体激励器产生的推力和吸力会逐渐减弱;而多级双极性等离子体激励器产生的推力和吸力均呈逐渐增强的趋势。     

齿位置对压气机级间封严影响的数值研究

通过对压气机级间封严不同齿位置时的流场和温度场进行数值模拟,获得其泄漏特性、旋流特性和风阻温升特性.研究单齿、双齿和三齿的相对位置对级间篦齿封严的流量系数、出口旋转比和风阻温升的影响.结果表明:单齿情况下,单齿在下游时的流量系数最小,出口旋转比和风阻温升最大.双齿情况下,上游和下游各一齿时的流量系数最小.三齿情况下,上、下游和中间各一齿时流量系数最小.出口旋转比和风阻温升都随流量系数的减小而增大.      

基于红外热像技术的涡轮叶片损伤评价研究进展

主动红外热像技术作为一种新型无损检测手段,具有高效率、无污染、易操作等特点,适合用于材料表面和近表面缺陷检测,因此在叶片类薄壁零件损伤评价方面有一定优势。当前基于主动红外热像无损检测技术的高温涡轮叶片损伤评价研究主要集中于热障涂层厚度检测、涂层脱粘检测、涂层界面处热生长氧化物检测以及叶片基体疲劳裂纹检测4个方面。但现有研究仍然面临热激励理论不完善、红外热像仪识别精度不够高以及热图处理方法有待改进等主要问题和困难。随着这些理论问题和技术困难的解决,主动红外热像技术呈现出人工识别缺陷向自动识别发展、定性检测向定量检测发展的趋势。总体而言,该技术未来在涡轮叶片损伤评价方面具有较大的应用潜力。     

航空表面涂层技术的应用与发展

航空表面涂层技术是航空制造技术的重要组成部分,涂层材料与涂层制造技术创新对提高航空零部件产品性能、降低能源消耗、提升产品可靠性及服役寿命具有重要意义.主要对涉及航空工业领域热障涂层、复合材料表面环境障涂层、高温可磨耗封严涂层及纳米涂层技术的应用现状与研究进展进行了阐述.     

氧化层非均匀增长对热障涂层应力分布的影响

利用扫描电镜对不同氧化程度的热障涂层(TBCs)进行观察,分析发现热生长氧化层(TGO)各部位并非均匀增长。假设热生长氧化层的形状为正弦曲线,用统计方法处理扫描电镜图片可以得到热生长氧化层的基本几何参数。由此建立单波形二维轴对称有限元模型,计算并分析了非均匀增长模型的应力状况。结果表明:相同温度下,非均匀增长模型的轴向、剪切和Mises应力分量的变化趋势与均匀增长模型的对应趋势一致;但是非均匀增长模型的各个应力分量最大值均小于均匀增长模型的应力分量最大值。      

电子束物理气相沉积LaZrCeO热障涂层微结构与热循环性能

热障涂层(thermal barrier coatings,TBCs)是一种由金属黏结层、热生长氧化物层和陶瓷面层组成的金属-陶瓷复合系统,在先进的航空发动机领域上引起了广泛的关注,但目前先进热障涂层的热循环寿命提升和失效行为研究仍然是一个难点。本研究采用电子束物理气相沉积技术(electron beam physical vapour deposition,EB-PVD)制备LaZrCeO/YSZ双陶瓷层热障涂层,研究热障涂层的相结构、显微组织和失效行为。结果表明:LaZrCeO/YSZ涂层为烧绿石与萤石结构组成的复合涂层材料,LaZrCeO/YSZ涂层的微观结构由羽毛状纳米结构和柱内孔隙组成;在1100℃热循环条件下,LaZrCeO/YSZ双陶瓷层热障涂层展现了良好的热循环寿命;热循环实验后,由于应力累积的作用裂纹在热生长氧化层(TGO)中萌生并扩展,包括水平裂纹和垂直裂纹两大类,进而引起整个涂层体系的不稳定,最终导致涂层失效。     

等离子涂层典型界面损伤与破坏的数值模拟

基于界面损伤力学思想,提出了三结点界面单元的概念,和传统界面单元相比,具有能够表征任意形状界面法线方向的优点,将改进的单元通过ABAQUS的用户子程序UEL与有限元软件进行了结合.考虑等离子涂层界面粗糙度的影响,模拟了余弦形界面在热循环载荷下的损伤以及在拉伸载荷下的破坏过程.计算结果表明,界面单元结点间位移出现不连续现象,体现了裂纹的逐渐张开过程,界面损伤随热循环次数的增加而增加,其中第一个循环造成的损伤最大,波峰处是界面断裂的危险位置,法向分离起主导作用;等离子涂层粗糙界面承受法向拉伸载荷的能力较平直界面显著增加.采用改进的界面单元模拟异质材料复杂形状界面的损伤与破坏是可行的,结果是合理的.      

ZrO2陶瓷热障涂层显微结构及隔热性能研究

用电子束物理气相沉积法(EB-PVD)在DZ125高温合金上制备Y2O3部分稳定化的ZrO2(YSZ)陶瓷热障涂层,并用扫描电镜(SEM)观察涂层显微结构.采用激光脉冲法对EB-PVD热障涂层的热扩散系数进行测试.为防止热扩散系数测试时激光穿透ZrO2陶瓷层,在试样表面制备不同材料的遮挡层.结果表明,EB-PVD热障涂层呈明显的柱状晶结构,柱状晶垂直于涂层/基体界面.基体的热扩散系数随温度的升高而急剧增加,陶瓷热障涂层的热扩散系数随温度的升高呈下降趋势,但变化幅度不大.室温下陶瓷层的热扩散系数小于基体的1/3,1200℃时约为基体的1/67.试样的激光遮挡层很好解决了激光脉冲法测试涂层热扩散系数时的不稳定性和激光穿透问题.在满足遮挡要求的条件下,遮挡层材料种类对热扩散系数测试无明显影响.     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.