自主火星探测高集成离子与中性粒子分析仪

小型化、高集成化是深空探测载荷发展的主要趋势。在我国自主火星探测计划中,设计了一种高集成化的火星离子与中性粒子分析仪。采用从传感器到电子学进行最大限度共用的设计思路,在一台仪器中实现对离子和能量中性原子进行能量、方向和成分的探测,大大降低了仪器对卫星平台的资源需求。仪器采取静电分析进行离子的方向和能量测量、采取飞行时间方法进行离子成分的测量。中性原子采用电离板电离成带电离子,后端的能量测量和成分测量与离子相同。鉴定件样机已经完成了初步的测试定标,结果表明其满足设计要求。     

载人航天器密封系统漏率设计方法

载人航天器密封舱为航天员提供在轨生活、工作的环境,对密封舱及其环控生保系统、热控制系统、推进控制系统等中各管路的密封性能有严格要求。文章提出了一种漏率设计方法,建立了相应的漏率检测系统,并依据该方法制定了密封舱体和各管路的漏率设计和指标分配的流程。本流程可用作载人航天器舱体密封系统、管路密封系统的漏率设计,对保证载人航天器在轨安全可靠运行有重要参考价值。     

多等级区域侦察弹性星座设计方法

针对传统侦察星座目标单一、弹性低的问题，提出了多等级区域侦察弹性星座的设计方法。该方法将星座设计过程按区域等级信息分为多个子星座逐步设计，直到整体星座对所有的区域性能满足设计要求。以区域被划分为3个等级为例，首先对星座设计需求、设计指标及设计步骤进行了分析。其次推导了地面最低分辨率和轨道高度的关系并确定了不同子星座的轨道高度。最后考虑轨道倾角、一箭多星发射、光照和升交点漂移同步约束，构建基础星座、子星座1和子星座2的优化模型。最终设计星座为3层混合星座，共8个轨道面和70颗卫星，星座对各等级区域的最大重访时间分别为10937s，12241s和17437s，弹性指数为2213%，2420%和6361%。结果表明该方法设计的星座可实现对区域覆盖和弹性分级的设计要求，证明了方法的有效性。对比Walker星座设计方法，在同等设计要求下，Walker星座所需卫星数为156颗，多等级区域侦察弹性星座所需卫星数远低于Walker星座，结果进一步证明了该星座设计方法的优越性。     

Experimental and numerical investigation on surface quality for two-point incremental sheet forming with interpolator

The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator.     

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

Applications of structural efficiency assessment method on structural-mechanical characteristics integrated design in aero-engines

In the design process of advanced aero-engines, it is necessary to carry out an effective analysis method between structural features and mechanical characteristics for a better structural optimization. Based on the structural composition and functions of aero-engines, the concept and contents of structural efficiency can reflect the relation between structural features and mechanical characteristics. In order to achieve the integrated design of structural and mechanical characteristics, one quantitative analysis method called Structural Efficiency Assessment Method (SEAM) was put forward. The structural efficiency coefficient was obtained by synthesizing the parameters to quantitatively evaluate the aero-engine structure design level. Parameterization method to evaluate structural design quality was realized. After analyzing the structural features of an actual dual-rotor system in typical high bypass ratio turbofan engines, the mechanical characteristics and structural efficiency coefficient were calculated. Structural efficiency coefficient of high-pressure rotor (0.43) is higher than that of low-pressure rotor (0.29), which directly shows the performance of the former is better, there is room for improvement in structural design of the low-pressure rotor. Thus the direction of structural optimization was pointed out. The applications of SEAM shows that the method is operational and effective in the evaluation and improvement of structural design.     

面向空间天线的TWF复合材料性能研究

利用碳纤维三向编织物（triaxial woven fabric，TWF）作为增强材料，与柔性基体材料硅橡胶复合，制成兼具一定柔性和刚性的复合材料壳膜结构，用于卫星天线反射器，是一种新型的高精度可展开天线实现方案。采用复合材料细观方法，对碳纤维增强硅橡胶TWF复合材料进行了力学性能的研究。首先由纤维和基体的材料特性得到均质纤维束的材料特性；接下来考虑纤维束交织情况（起伏波动）建立由纤维束组成的单胞实体有限元模型；然后对单胞实体有限元模型进行均匀化分析，施加周期性边界条件，最终得到等效的均质材料特性；为满足天线反射器高性能需求，分析了碳纤维种类、纤维体积分数对单胞等效性能的影响规律。对该材料力学性能的研究，可以为其未来应用于大型高精度可展开天线反射器提供一定的理论依据。     

企业知识生态系统内生与外生协同机制研究

通过对企业知识生态系统协同机制的研究,设计知识生态系统内生和外生协同机制.内生协同机制包括企业知识生态系统战略协同机制、内部环境协同机制、领导协同机制、知识主体协同机制、激励协同机制的设计.外生协同机制包括外部环境协同机制设计、行业发展协同机制设计、技术协同机制设计,从而保障企业知识生态系统正常运行.     

某框基于后置程序逆向设计及数字化高效加工研究

介绍了飞机某框从逆向设计到数字化高效加工详细流程,应用以CATIA V5、VERICUT为代表的先进数字化制造技术,使零件数字化设计、数字化加工、工艺流程得到全面改进,为今后零件逆向设计及数字化加工奠定良好的基础。     

Multiscale topology optimization using feature-driven method

This paper presents a multiscale design method for simultaneous topology optimization of both macrostructures and microstructures. Geometric features are extended as design primitives at both macro and micro scales and represented by Level Set Functions (LSFs). Parameters related to the locations, sizes, and orientations of macro and micro features are considered as design variables and optimized simultaneously. In the overlapping areas of different macro features, embedded microstructures are optimally figured out as the solution of the corresponding sub-optimization problem. In this study, the eXtended Finite Element Method (XFEM) is implemented for structural and sensitivity analyses with respect to design variables. This method has the advantage of using a fixed grid independent of the topology optimization process. The homogenization procedure is applied to calculate the effective properties of considered microstructures in each macro feature. Numerical examples are presented to illustrate the effectiveness of the proposed method. Results depict that the multiscale design cannot obviously improve structural stiffness compared with a solid-material design under the linear elastic condition.