GH169合金细晶锻造工艺研究

为了提高涡轮盘的强度和低周疲劳性能,要求锻件具有ASTM10级以上的细晶组织国外在大型压力机上采用低温大变形锻造和直接时效热处理以获得性能良好的细晶锻件,而我国则试图采用锻锤生产GH169合金涡轮盘锻件,因此,需要探索适合国情的GH169合金细晶锻造工艺。根据以往的研究,δ相对GH169合金的显微组织有明显影响,因而可     

航空发动机全程滑态变结构控制研究

一种新的滑模变结构控制方法-全程滑态变结构控制首次应用于航空发动机控制系统，该控制方法能有效地缩短系统状态到达滑动模态的时间，避免了定常滑态变结构控制系统在能达阶段对扰动的敏感性，且其控制律的设计可以改善系统的瞬态性能，克服未知参数摄动的影响，仿真结果表明，基于全程滑态变结构控制所设计的发动机控制系统，其鲁棒性要优于发动机定常滑态结构控制系统。     

民用飞机机翼副油箱静载荷计算

以亚音速、大展弦比的大中型民用飞机机翼挂装副油箱为研究对象,分析CCAR-25部中载荷计算的相关适航条款内容,考虑外挂物自身运动及机翼结构弹性变形对副油箱气动载荷的影响,给出了副油箱静载荷计算的过载—速度包线,高度—速度包线、载荷计算情况等,在工程应用成熟的《运输类飞机载荷计算程序包》基础上,采用亚音速稳态定常流升力线理论与风洞试验相结合的方法,将机翼简化为悬臂梁进行气动弹性修正,开展副油箱气动力弹性修正计算、惯性力计算、副油箱质量实时更新、包线筛选等功能模块的研究,通过工程应用其计算精度满足要求,形成了满足适航条款的副油箱静载荷计算方法,规范了副油箱静载荷的计算流程,拓展了《运输类飞机载荷计算程序包》的功能。     

高科技与微型涡轮发动机的研制

在收集、分析国外某些微型涡轮发动机的文献和实物的基础上，结合参加自行设计微型涡轮发动机的体会，提出应用现有的和正在发展中的新技术、新材料、新工艺，将对微型涡轮发动机的性能和研制周期产生较大的影响。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

建立民航维修专家系统的分析

简要介绍了专家系统的原理及构成.分析了“设计民航维修专家系统”的过程,目前加拿大正着手研制的“先进的维修软件系统”的概况.最后提出专家系统需要解决的关键技术问题及发展情况.     

地面对带后缘分离的翼型绕流影响的计算

本文提出了用在地面上分布奇点来模拟地面的方法。计算结果与精确解和镜像法结果很吻合。     

飞机座舱有机玻璃机械加工应力测量方法研究

 通过实验研究了有机玻璃由于机械加工所产生的双折射条纹的性质及其与机械加工应力的关系;建立了一种定量测定和无损检测平板有机玻璃和飞机座舱有机玻璃件机械加工应力的新方法:用光弹性仪可以测得与双折射有关的干涉条纹,则可确定加工应力。     

地面涡研究

 The formation mechanism and the flow characteristics of the ground vortices as well as the method of eliminating ground vortices are studied in this paper. It is noted that, when air is sucked into an aircraft engine, on the ground a momentum moment is exerted on a point sink flow by a lateral wind or a reversed jet from the tail pipe, resulting in the formation of eddy stream known as ground vortices. Through an analysis of numerous experimental data it is found that the ground vortices are composed of two vortices instead of a single and concentrated free vortex.The tangitial velocity distribution curves of the ground vortex can be expressed as two independent functions: one is a directly proportional function located at the core, and the other is an inversely proportional function around the outer surrounding. The pressure distribution is also composed of two parabolic functions.In addition, a method of eliminating the ground vortices is presented, and it is of important engineering significance to eliminate the ground vortices.     

美陆军制导武器试验半实物仿真技术综述

主要综述美国陆军制导武器试验的仿真技术和设施，同时介绍仿真试验中使用的几种典型的目标景象投影技术，并说明了它们的应用范围和优缺点。最后介绍了当前制导武器试验仿真技术的发展趋势。